Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Zero Tolerance 0560/0561 3.75 in 0.157 Elmax 60 left 25/right 26 3.5 micro leather bottom B.5 EDC
 
Authors Comments:Not the sharpest thing in the world but will keep that edge for quite some time.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JosephMurray
Rating:
Rating:
Rating:
Rating:
Rating:
Matt Diskin Hand-Ground Fire D/A 3.625 0.13 Elmax N/A: Prob low 60's 22 per side 1000 and then polished with Edge-Pro polishing tapes up to 6000 before stropping on 0.25 micron strop T B EDC
 
Authors Comments:Exceptional knife and takes an insane edge. Easily whittles hair.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
Rating:
Rating:
Rating:
Rating:
Mora Utility knife 100 mm 1.9 mm Hi-Carbon steel 57 22 0.6 um micro fine T A.5 Dirty work around the house, cables, boxes...
 
Authors Comments:Very difficult to really reach in to the blade close to the handle due to the quillon / hilt (alomst need a re-clamp).
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Gerber EZ Out 3 .1 high carbon stainles n/a 17.5 1000# then 5-3.5 leather strops Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
1000# 17.5 deg., stop @ 16.5

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Finn Bear 4" 2.5 mm Krupp 4116 Stainless HRC 56-57 19.5 (39 inclusive) .5um Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Kudu 4.25" 2 mm Krupp 4116 Stainless HRC 56-57 17 0.5um 1st B.5
 
Authors Comments:Shaving sharp and mirror polish after finishing with the 1/0.5um diamond spray on leather
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Fällkniven NL5 IDUN 100 mm 5 mm Lam.VG10 59 HRC 18/19/20 1000# Diamond / 1600# Ceramic | blending 14/10 strops, 1/,5 strops top B bushcraft
 
Authors Comments:I have now tested the edge with a lot of whittling, edge shaved but not easily, stropping on 19 degrees took it back to a good razoredge.. Tony Pettersen "EDIT OUT - i think someone have placed their comment on this knife by mistake, idun is no lockback - EDIT OUT"
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Benchmade 581 Barrage 3.60" .121" M390 60-62 17 deg. (measured) .5m Leather (although lightly stropped so not a mirror finish). Top B EDC
 
Authors Comments:1st time w/ M390 steel. Slightly lowered factory bevel and cleaned up the edge (came with a very rough finish). See how it holds up at this angle.
Angle/Finish Tried with Ratings
Setting 1:
A.5 and 17.5º

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: cbwx34
Rating:
7
Rating:
Rating:
Rating:
Rating:
Anders Petter Paring knife 100 mm 1.35 mm Molybdenum stainless 57 21 0.6 um micro fine T B.0 Fruit and small veggies in kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Anders Petter Chef knife 200 mm 2 mm Molybdenum Stainless 57 22 0.6 um micro fine B D.0 Kitchen use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:


Page 11 of 18 Results 101 - 110 of 172