Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Spyderco Police 4.125 .125 VG-10 Unknown 19 1000, 6 micron strop , 3 micron strop Top B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Leaf Storm 2.125" .125" CPMS30V unknown 15 1000 Grit Short Short, very short Pocket knife
 
Authors Comments:NA
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Delica 4 2.875" 2.5mm VG-10 N/A 20 degrees 3.5 micron strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Paramilitary 2 CF 3.44 1.41 S90V 62 19 L - 20 R 3.5 um Bottom A.5
 
Authors Comments:Maintains the manufactures angle
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Fred Perrin Street Beat 3.5 inches 5/32th of an inch VG-10, 59 17 degrees per side ceramics and strops 5 and 3.5 diamond paste Top B-1 EDC / Tactical fixed blade
 
Authors Comments:Fred Perrin is an ex-special forces France knife designer and he has made a scary little knife here. It is full flat ground, so needs special attention when mounting. I use chamois to fill the voids.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Leo James Mitchell
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Delica 4 2.88 0.093 ZDP-189 64 17, Mirco 20 3.5 um @19 Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: TPeters
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Gayle Bradley 3.5 1/8 CPM M4 I think about 62 RC 15 1 micron boron carbide(HandAmercian) on balsa Top B EDC
 
Authors Comments:I like this steel. It takes a variety of finishes well but for EDC I like a congress 400 or the 1000 diamonds followed by 1 micron boron carbide paste on balsa the best. This seems to be about where hair whittling starts but it still has some bite. Hope you like it as much as I do.
Angle/Finish Tried with Ratings
Setting 1:
17 degrees 1000 diamond 3.5 paste on balsa

Setting 2:
15 degrees 1000 diamond 1 BC on balsa

Setting 3:
15 degrees 400 congress 1 BC on balsa

Setting 4:
15 degrees all the way to .125 CBN on roo

Setting 5:


Author: guest
Rating:
6
Rating:
7
Rating:
9
Rating:
8
Rating:
Spyderco Native 3 1/16" 1/8" S30V 59-60 HRC 18 deg. Micro Fine Fine Top A 3/4 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: cbwx34
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Endura 4 FFG 3.75" 0.125" VG-10 HRC 59-61 15 0.5um 2 B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Tenacious 3.39" 0.118" 8Cr13MoV HRC 58-59 15 0.5um 2nd B.5
 
Authors Comments:Shaving sharp and mirror polish after finishing with the 1/0.5um diamond spray on leather
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:


Page 3 of 18 Results 21 - 30 of 172