Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Cutco 9 1/4" Chef Knife, Item # 1725 9.25 - 440A - 17 1000# Bottom D kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
1000# 17 deg.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT 4102 Michael Walker BladeLock II 2.875" Unknown AUS-4 Unknown 15 1600# Ceramic Top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
CRKT Folts Minimalist 127mm 2.1mm 5Cr15MoV 57 RC 19 5u Lap Top 30mm Tip to CL/Vise EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
reprofile to 19, finish 1000 diamond

Setting 2:
reprofile to 19, then finish at 0.3u

Setting 3:
0.3 lap then fine strop .5u on leather

Setting 4:


Setting 5:


Author: BassLakeDan
Rating:
5
Rating:
8
Rating:
6
Rating:
Rating:
CRKT M16-13T 3.5" 0.110" AUS8 58-59 Asymmetrical grind (70/30), I used left 20, right 15 to get close and finished the profile that way 1k diamond -> 5um strop for finish and touchup Unique (see comment) B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT Ripple 3.125 .107 8CR14MoV 59-60 l 20/r 20 .05 strop top a5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT Onion-Shenanigan #K470KKP 3.25 inch 0.119 inch / 3.0mm Acuto 59-60 HRC 20* 0.6 ceramic Upper holes B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M21-14SF 3.875 inches 0.14 inches AUS 8 58-59 18.5 5 micron Bottom A 0.5 Put a usable polished sharp edge in place.
 
Authors Comments:I will test the durability and usability of this edge in the coming weeks.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
10
Rating:
Rating:
Rating:
Rating:
Crkt 5470 lg Fossil 3.960 0.15 8Cr13Mov 58-60HRC 18 5.0 diamond paste strop 2 C EDC
 
Authors Comments:Creates a beautiful razor edge!
Angle/Finish Tried with Ratings
Setting 1:
10

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: tnbusarider
Rating:
10
Rating:
Rating:
Rating:
Rating:
Cold Steel Black Sable 4" .125" San Mai III 58 HRC 18 primary bevel, 19 degree micro bevel 1600# Top B.5 EDC
 
Authors Comments:I originally created the bevels at 18 degrees and polished them to .5 microns before adding a micro-bevel at 19 degrees with the 1600# ceramic stones to give a mirrored bevel and slightly reduced shoulder while making the actual edge a little wider and giving it some micro teeth.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1


Page 12 of 18 Results 111 - 120 of 172