Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Delica 4 2.88 0.093 ZDP-189 64 17, Mirco 20 3.5 um @19 Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: TPeters
Rating:
Rating:
Rating:
Rating:
Rating:
Remington Swift-Lokt Assited Opening Folder 3.125 inches .134 inches 440A 56 17 degrees per side ceramics and strops Top B-1 general use EDC, good in the kitchen, backyard or
 
Authors Comments:My wife loves this knife. It takes a good edge and is easy to resharpen. It gets a lot of use by everyone. LJM
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Leo James Mitchell
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Fred Perrin Street Beat 3.5 inches 5/32th of an inch VG-10, 59 17 degrees per side ceramics and strops 5 and 3.5 diamond paste Top B-1 EDC / Tactical fixed blade
 
Authors Comments:Fred Perrin is an ex-special forces France knife designer and he has made a scary little knife here. It is full flat ground, so needs special attention when mounting. I use chamois to fill the voids.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Leo James Mitchell
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Bark River Bravo 1 4.250 inches .215 inches A-2 tool steel 59 17 degrees ceramics and strops with 5 and 3.5 micron pastes, I do a lot of stropping with green paste day to day and so I get a convexing to this edge over time top B-5 survival/bushcraft/tactical
 
Authors Comments:LJM it originally came with a zero degree convex edge which I found was a bit too fine and subject to chipping and rolling; I love the 17 degree angle razor sharp and tough
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Chris Reeve Large Sebenza 3.625" 0125" S35VN 58-59 RC 17 Deg. with 18 Deg. Microbevel 17 Deg. finished at 3.5u Strop Top Holes A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
17 degree main bevel 18,19,20,21 micro for convex

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
9
Rating:
Rating:
Rating:
Rating:
Benchmade 581 Barrage 3.60" .121" M390 60-62 17 deg. (measured) .5m Leather (although lightly stropped so not a mirror finish). Top B EDC
 
Authors Comments:1st time w/ M390 steel. Slightly lowered factory bevel and cleaned up the edge (came with a very rough finish). See how it holds up at this angle.
Angle/Finish Tried with Ratings
Setting 1:
A.5 and 17.5º

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: cbwx34
Rating:
7
Rating:
Rating:
Rating:
Rating:
Kershaw Blur 3.3125" .125" ZDP-189 64HRC 17 1um Bottom. A.5 EDC (Every day carry)
 
Authors Comments:After several months of experimenting, I've settled on 17 degrees for this knife. It gives great performance and holds its edge well. I keep it pretty polished for show and sometimes it's a little too smooth for the work it does so I might put a slightly toothy, almost invisible micro-bevel on it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Mora Calssic 2 10.5cm 2mm Carbon 59-60 RC 17 15u top 55mm tip to CL/Vise Camp Utility Knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
7
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kershaw Leek 1660BR 2.825 .09 Sandvik 14C28N unk 17 .6 ceramics top A EDC backup
 
Authors Comments:nice knife for an office enviroment (not too threatning) seems to hold the edge pretty well with minimal touching up so far. Haven't used it for anything heavy duty yet, though.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:


Page 13 of 18 Results 121 - 130 of 172