Ralph, you're right I just goofed up my answer. I stropped with the roo at 25 and used the .6 ceramics at 30! Thanks for catching it.

RalphHoneycutt wrote:

Bumping this up. Have some questions here (actually searched the forum rather than starting a new thread).

1.) Does anyone have feedback on best performance (sharpness, edge quality) of leading vs. trailing.

2.) Does anyone do both leading and trailing? I was trying 5 each, then finishing 1 each way. After looking at Clay's photos, would alternating leading/trailing stokes clean up the burr on the bevel and the edge?

3.) Feedback on direction - tip to heel or vice versa? Do you roll the tip less by going tip to heel? (or do I just need more practice?) I did find the mixing tip => heel and heel => tip seems very rough, like going against the grain. Or is this good? Does switching directions get the scratches out or just make more/worse?

Geocyclist wrote:


Here's my .02

1. On some knives I can't tell. On knives that I have an issue with... primarily a burr that won't go away, edge leading works best for me at cleaning it up. If I'm trying to get a knife as sharp as I can, I find edge leading, especially with the ceramics, gives me a better edge.

2. On the WE I primarily do edge trailing. I never do edge leading with the coarse stones.

3. With the coarse stones I do heel to tip, seems to be the quickest way to set up the edge. From 600g on, I'll do heel to tip, then I'll do 10-20 strokes tip to heel before moving to the next stone. With the finest stone or strop I plan to finish with, the majority are tip to heel. Switching cleans up the bevel better, and finishing tip to heel sets the "teeth" for better slicing. Even with a polished finish, I see a difference. (All this is edge trailing).

Not set in stone "rules", just a general pattern I tend to follow on the WE.

I tried your technique with my CRKT Ripple and I have to say, it's probably the sharpest blade I've done so far. I also now have the upgraded ball arms and paid special attention to keeping pressure very light. Still, it was able to shave facial hair in relative comfort, and other hair was no issue whatsoever! I shouldn't have changed so many variables at once to get a better idea of what is making the greatest difference, but it has to be the combination of all. Light touch is key. I'm now a believer.

cbwx34, why do you not do edge leading with coarse stones?

I noticed an improvement on my last knife by doing both heel to tip and tip to heel, finishing each stone with tip to heel. I can feel/tell I am working the scratches out. The sharpness was better also.

For a re-profile I do scrubbing strokes to get a burr with 100# stones. Then from there its alternating strokes.

I know you were asking Curtis. I can just throw in how I do things and why I do not alternate at lower grit levels.
I run through all of the stones until about the 3K Choseras.. including (today anyway) the WEPS ceramics edge trailing. In the past I have done everything edge trailing. Not sure I can get anything any sharper...

Lately with the real fine stones I have been doing ... depending on OCD level, about 100 strokes edge trailing, 30 or so edge leading and a few edge trailing. The dge leading strokes at the higher grits can get rid of the very fine scratches a bit faster... but not so much that I worry about it... nor can I see it without lots of magnification. So... why? Because it is easier for me to do with the level of coordination that I possess. I can control the paddles consistently better... I think, being consistent is as important as anything that I do while sharpening. Muscle memory is very important in getting there.

Some folks have said that they can cut some things better by angling the scratch pattern toward the heel,,
I think they are talking about lower grits. I have a knife prepped up to the 5K choseras... I will go to 10K and a bit of stropping. Then, as Clay suggested increase the angle by a degree and go down to the 1200 cermaics. Usually I would just do this edge trailing... because that is what I do. Maybe I can do that.. do some tests, and go back and try edge leading for a few strokes. See if I find any improvement. If I do, maybe I work a new wrinkle into my progression.

I think,if you feel you are getting blades sharper with one direction over the other, it could be the direction that you leave the "tooth" pattern. For a couple of years and lots of knives ...hair whittling, hair tree topping, rope parting from 2 inches away (not really ) I am not sure that I can improve sharpness results from the primarily edge trailing method... though cosmetically I have seen faster scratch removal by alternating..

Bottom line, why do I do it that way... because I am comfortable with it and it works for me... I get great results.

Of course, as always, do what works for you.. It is always great ot hear what others do to get good results!


Phil