Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Hogue EX01 Tanto 4" 0.15" 154CM 57-59 22 1k diamond, any diamond paste strop for personal taste. Handles micro-bevels very well! Top B.5 Heavy duty utility/carry
 
Authors Comments:The cosmetic jimping on the spine makes a great reference point on the depth key pins
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Kabar K2 Chinchete 3.25" 0.15" 3CR13 50-52 18 3.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M21-14SF 3.875 inches 0.14 inches AUS 8 58-59 18.5 5 micron Bottom A 0.5 Put a usable polished sharp edge in place.
 
Authors Comments:I will test the durability and usability of this edge in the coming weeks.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
10
Rating:
Rating:
Rating:
Rating:
Buck Zipper. 191 4 1/8 inch 0.14 inch 420HC ? 18/side. Leather strop 1mic Upper B.5 Skinning fixed blade
 
Authors Comments:Buck states factory angles are 13-16/side. This was closer to 18/side. Diamond 400 - 1000. Ceramic 1.4 then leather strops as noted in finish.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Benchmade 915 Triage 3.5" 0.13" N680 57-59HRC 20 1um Strops Bottom B
 
Authors Comments:I rested the spine on the closest pin of the depth key and then rotated the blade until most of it was parallel to the base of the sharpener.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Twitch XL 3.25 0.13 AUS-8 RC 57-58 22 3.5u Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: SleeplessJunkie
Rating:
Rating:
Rating:
Rating:
Rating:
Chris Reeve Small Sebenza 2.94in 0.125in S35VN 58-59 RC 22 Degrees 3.5um Top A 1/2 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Endura 4 FFG 3.75" 0.125" VG-10 HRC 59-61 15 0.5um 2 B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:


Page 8 of 17