Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Benchmade 553 Tanto 3.5 .115 154CM 59 18 .05 strop with a 1600 microbevel @22 top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
18 degrees to .05 strop

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
8
Rating:
Rating:
Rating:
Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: EatingPie
Rating:
7
Rating:
Rating:
Rating:
Rating:
Emerson CQC-8 100 mm 3 mm 154CM? 57-59 23 1000# Diamond Bottom B Hard use survival / bushcraft
 
Authors Comments:This folder is from 2004 without wave. I have a V-grind on this one.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: jolut
Rating:
Rating:
Rating:
Rating:
Rating:
Fallkniven PXL Folder 3.4 inches .138 3 G Powder steel lam 62 16 ceramics and strops Top B EDC
 
Authors Comments:This is my favourite EDC knife. It is pretty and it is sharp in the extreme. I give this knife a five out of five for looks, usefullness and strength.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kabar K2 Chinchete 3.25" 0.15" 3CR13 50-52 18 3.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Fallkniven TK-1 4 inches .18 inches 3G laminated powder 62 21 degrees ceramics and strops with 5 and 3.5 micron pastes Top B.4 bushcraft
 
Authors Comments: LJM
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Fallkniven SK-1 3.88 inches .18 inches 3G laminated powder 62 16 degrees ceramics and strops with 5 and 3.5 micron pastes Top B.3 Bushcraft
 
Authors Comments:LJM
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Smith SWBLOP3 3.4 ? 4034 ? 20 3.5 mu ? B ever day use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MelvinSharp
Rating:
Rating:
Rating:
Rating:
Rating:
Leatherman PST-original Leatherman multi-tool 2.9 inches ? 420 HC STAINLESS ? 20 1200 ceramic Above upper holes A.5 Multi tool/ anything goes
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:


Page 3 of 18 Results 21 - 30 of 172