Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Spyderco Manix 2 CF 3.375" .125" S90V unknown 15 3.5um Bottom. B.25
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Paramilitary 2 CF 3.438" .141" S90V unknown 15 3.5um Bottom. B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Paramilitary 2 CF 3.44 1.41 S90V 62 19 L - 20 R 3.5 um Bottom A.5
 
Authors Comments:Maintains the manufactures angle
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Cold Steel Old small folder 2.5 inches ? San Mai 3 ? 56-58 HRC ? 18.4* 0.6 mic ceramic Upper holes A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Black Sable 4" .125" San Mai III 58 HRC 18 primary bevel, 19 degree micro bevel 1600# Top B.5 EDC
 
Authors Comments:I originally created the bevels at 18 degrees and polished them to .5 microns before adding a micro-bevel at 19 degrees with the 1600# ceramic stones to give a mirrored bevel and slightly reduced shoulder while making the actual edge a little wider and giving it some micro teeth.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kershaw ET 3.25" 0.120" Sandvik 14C28N Not listed 20 1000 grit diamond, 5um paste on leather optional Top A.5 General light utility
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Kershaw Leek 1660BR 2.825 .09 Sandvik 14C28N unk 17 .6 ceramics top A EDC backup
 
Authors Comments:nice knife for an office enviroment (not too threatning) seems to hold the edge pretty well with minimal touching up so far. Haven't used it for anything heavy duty yet, though.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Spec Elite 1 3.75" 1/8" Seki Japan VG10 60-61 HRC 16 degrees 3.5micron shallow dept C thumb knob onClamp EDC light to moderate use
 
Authors Comments:difficult to set up in Clamp, recommend removing thumb knob for sharpening entire blade length
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Oxo Good grips paring 4 inches ? Stainless ? 18 1000 diamond Above upper holes B General kitchen duties
 
Authors Comments:4/2/13 trying 2* bevel at 20* with 1000 diamond
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Kongsberg Norway Mora like utility knife 100 mm 2.0 mm Unspec. HiCarbon 56 22 0.6 um micro fine T A.5 Chopping, boxes, rope, branches, prying.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:


Page 14 of 17