Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
CRKT M16-13T 3.5" 0.110" AUS8 58-59 Asymmetrical grind (70/30), I used left 20, right 15 to get close and finished the profile that way 1k diamond -> 5um strop for finish and touchup Unique (see comment) B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
10
Rating:
Rating:
Rating:
Rating:
CRKT M21-14SF 3.875 inches 0.14 inches AUS 8 58-59 18.5 5 micron Bottom A 0.5 Put a usable polished sharp edge in place.
 
Authors Comments:I will test the durability and usability of this edge in the coming weeks.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Manix 2 CF 3.375" .125" S90V unknown 15 3.5um Bottom. B.25
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Manix 2 CF 3.375" .125" CTX-XHP unknown 15 3.5um Bottom. B.25
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Cold Steel Master Tanto 6" .1875" VG1 San Mai III 56-58RHC 25 .5um Bottom B.5 Tactical
 
Authors Comments:I inherited this knife from my step father who carried it overseas for many years. It had been hand sharpened for years so it's hard to know what the original angle was. Reprofiling it took some time but it finished up nicely and took a super polish.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Buck Metro (759) 1" ? 420HC ? 17 1000# daniel, a few light cleanup passes with 5um leather See comments A.5 EDC
 
Authors Comments:Clamp on the bottle opener ring, the aluminum body section will control depth. Align to A.5 and level out the little blade with the clamp as best you can! Works surprisingly well.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Military CF 4" .156" S90V unknown 15 3.5um Bottom. B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Gerber Mini Covert 3" 0.110" 154CM Not listed 19 1k diamond for duty/carry, but takes well to full out mirror polish too! Top A.5 EDC
 
Authors Comments:In matching the factory bevel, an even 19 degrees per side ends up 18 on the left arm and 20 on the right arm. Thus far the 19 degree edge has held up very well, as a 154CM should!
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Benchmade Mini-Griptilian - Doug Ritter 2.88 .1 S30V 62 22 1600 Ceramic Bottom A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:


Page 10 of 17