Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
KAI/Zero Tolerance 0560 3.75 0.157 Elmax 60-61 20 10K Choseras Bottom. B 0.25
 
Authors Comments:The 10K Chosera edge is not really functional (unless you want to cut single sheets of paper). But it looks great.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Zero Tolerance 0560/0561 3.75 in 0.157 Elmax 60 left 25/right 26 3.5 micro leather bottom B.5 EDC
 
Authors Comments:Not the sharpest thing in the world but will keep that edge for quite some time.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JosephMurray
Rating:
Rating:
Rating:
Rating:
Rating:
Zero Tolerance 0700 3.375" Unknown S30V Unknown 14.5 As Measured (15 Degree Slot) 3u Balsa 1u 3M PSA Tape (200 Passes Each) Top B.0 EDC / Boxes / Paper
 
Authors Comments:Tape thumb studs because stones may rub them. S30V is some hard steel!. Great Tanto Shape. My Favorite Blade!
Angle/Finish Tried with Ratings
Setting 1:
14.5 EDC / Paper / Boxes with Mirror Bevel

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: EatingPie
Rating:
10
Rating:
Rating:
Rating:
Rating:
Kabar 1100 stockman pocket knife 2.5 inch ? ? ? 21.75 Ceramic 0.6 micron Above upper holes A.5 Toolbox
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Buck 112 3" .077 420HC 58-61 18, 20 Micro 3.5 um@18, 1600@20 Top B Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Buck 119BKS-B 6 ? 440C ? 20 3.5um Bottom C Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
Buck 119BKS-B 6 ? 440C ? 20 3.5um Bottom C Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Camillus 18671 3 in. .120 in. VG-10 Unk. 21 deg. 10m leather (just a light strop) Top A 1/2 EDC
 
Authors Comments:Blade has a "Carbonitride Titanium" coating, which the manufacturer claims makes it "10x harder". Anyway, my intent was to match the original bevel, but at 25 deg. I was still hitting near the shoulder, so decided to stop at 25. Blade came out sharp, but would probably benefit from a lower angle. 2/16/13 EDIT: I resharpened this knife, and when I set the bevel, it matched at 21 deg. I don't know why the difference from the previous 25 deg. but thought I'd document the difference.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
Rating:
Rating:
Rating:
Rating:
Cutco 2 3/4" paring Item # 1720 2.75 - 440A - 17 1000# then 5-3.5 leather strops spine only in vice A.5 kitchen, general use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
A.5, 17 deg.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
7
Rating:
Rating:
Rating:
Rating:


Page 1 of 17 Results 1 - 10 of 168