Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Oxo Good grips paring 4 inches ? Stainless ? 18 1000 diamond Above upper holes B General kitchen duties
 
Authors Comments:4/2/13 trying 2* bevel at 20* with 1000 diamond
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Mora Calssic 2 10.5cm 2mm Carbon 59-60 RC 17 15u top 55mm tip to CL/Vise Camp Utility Knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
7
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Mora Frost Exclusive 345 125 mm 3 mm ? ? 22 1000# Diamond Top C Outdoor / fishing
 
Authors Comments:This is a knife I have been using since the late '70.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: jolut
Rating:
Rating:
Rating:
Rating:
Rating:
Mora Utility knife 100 mm 1.9 mm Hi-Carbon steel 57 22 0.6 um micro fine T A.5 Dirty work around the house, cables, boxes...
 
Authors Comments:Very difficult to really reach in to the blade close to the handle due to the quillon / hilt (alomst need a re-clamp).
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Leatherman PST-original Leatherman multi-tool 2.9 inches ? 420 HC STAINLESS ? 20 1200 ceramic Above upper holes A.5 Multi tool/ anything goes
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Leatherman Super Tool (original) 3" n/a n/a (cheap) n/a 22 1000# then 5-3.5 leather strops spine only in vice A .5 EDC
 
Authors Comments:set blade high in vice, only the square part of spine in vice
Angle/Finish Tried with Ratings
Setting 1:
lower in vice with depth key at high

Setting 2:
22 deg, 1000#, 3.5u strops, depth higher, see comm

Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
4
Rating:
6
Rating:
Rating:
Rating:
Kongsberg Norway Mora like utility knife 100 mm 2.0 mm Unspec. HiCarbon 56 22 0.6 um micro fine T A.5 Chopping, boxes, rope, branches, prying.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Knives of Alaska Steelheader 5.75 ? 440C 58-60 18 1000# Top D Fillet Knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: TPeters
Rating:
Rating:
Rating:
Rating:
Rating:
Kershaw Blur 3.3125" .125" ZDP-189 64HRC 17 1um Bottom. A.5 EDC (Every day carry)
 
Authors Comments:After several months of experimenting, I've settled on 17 degrees for this knife. It gives great performance and holds its edge well. I keep it pretty polished for show and sometimes it's a little too smooth for the work it does so I might put a slightly toothy, almost invisible micro-bevel on it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1


Page 6 of 17