Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Cold Steel Master Tanto 6" .1875" VG1 San Mai III 56-58RHC 25 .5um Bottom B.5 Tactical
 
Authors Comments:I inherited this knife from my step father who carried it overseas for many years. It had been hand sharpened for years so it's hard to know what the original angle was. Reprofiling it took some time but it finished up nicely and took a super polish.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Cold Steel Finn Bear 4" 2.5 mm Krupp 4116 Stainless HRC 56-57 19.5 (39 inclusive) .5um Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Twist Master 3.5 ? Carbon V ? 17.3 8k Naniwa super stone Upper holes B EDC
 
Authors Comments:Diamond 400-1000. Ceramic 1200-0.6. Naniwa 8k. Bought several of these as close outs/ factory 2nds About 20 years ago. Takes a nice edge easily and keeps it well. Rusts easily.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Kudu 4.25" 2 mm Krupp 4116 Stainless HRC 56-57 17 0.5um 1st B.5
 
Authors Comments:Shaving sharp and mirror polish after finishing with the 1/0.5um diamond spray on leather
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Old small folder 2.5 inches ? San Mai 3 ? 56-58 HRC ? 18.4* 0.6 mic ceramic Upper holes A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Voyager (Medium Tanto) 3" 3 mm AUS 8A HRC 57-59 19 3.5um 1st A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Recon 1 Tanto Plain 27TLT 4" 3.5mm AUS 8A Stainless Unknown 19.4 Measured (I align using divots, hence weird angle) 3u Balsa Top B.5 Scaring People
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
19.4 Measured.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: EatingPie
Rating:
6
Rating:
Rating:
Rating:
Rating:
Chris Reeve Large Sebenza 3.625" 0125" S35VN 58-59 RC 17 Deg. with 18 Deg. Microbevel 17 Deg. finished at 3.5u Strop Top Holes A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
17 degree main bevel 18,19,20,21 micro for convex

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
9
Rating:
Rating:
Rating:
Rating:
Chris Reeve Small Sebenza 21 2.94" .125" S35VN Stainless Stee 58-59 RC 18 deg. with 19,20 deg. Micro bevel for convex 18 Deg finished with Roo Strop .125 CBN and blank Top Holes B EDC
 
Authors Comments:All angles set with Angle Cube, rechecked on each stone. Re-created 18 Degree bevel with Diamond 400 -1000, Ceramic 1200/1600 then 5000/10000 Chosera. With 5/10k Chosera reset angle to 20 , 19 then back to 18deg. to define convex. Continued with Balsa 20, 19 then 18deg. with .5 Microne paste Completed at 18deg finish with Roo with .125 Cubic Boron then blank Roo with a mist of alcohol. Shaving sharp and developing a nice mirror polish edge. Maintenance additional careful stropping will r
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JamesBell
Rating:
Rating:
Rating:
Rating:
Rating:
Chris Reeve Small Sebenza 2.94in 0.125in S35VN 58-59 RC 22 Degrees 3.5um Top A 1/2 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:


Page 13 of 18 Results 121 - 130 of 172