Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
CRKT Onion-Shenanigan #K470KKP 3.25 inch 0.119 inch / 3.0mm Acuto 59-60 HRC 20* 0.6 ceramic Upper holes B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Visionary 1 3" .12" VG-10 59-60 23 to 25 1000 Top A .5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
SOG X Ray Vision Mini 3" .12" VG-10 59-60 23 to 25 1000 Top A .5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
CRKT Ripple 3.125 .107 8CR14MoV 59-60 l 20/r 20 .05 strop top a5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Vulcan 3.25 .157 VG-10 59-60 l 17/r 21 .05 strop top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
Fällkniven NL5 IDUN 100 mm 5 mm Lam.VG10 59 HRC 18/19/20 1000# Diamond / 1600# Ceramic | blending 14/10 strops, 1/,5 strops top B bushcraft
 
Authors Comments:I have now tested the edge with a lot of whittling, edge shaved but not easily, stropping on 19 degrees took it back to a good razoredge.. Tony Pettersen "EDIT OUT - i think someone have placed their comment on this knife by mistake, idun is no lockback - EDIT OUT"
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Fallkniven A1 6.3 0.24 VG-10 59 15 1600 Low B 0.75
 
Authors Comments:I put a 15 degrees microbevel on top of a 13 degrees convex edge
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Bark River Bravo 1 4.250 inches .215 inches A-2 tool steel 59 17 degrees ceramics and strops with 5 and 3.5 micron pastes, I do a lot of stropping with green paste day to day and so I get a convexing to this edge over time top B-5 survival/bushcraft/tactical
 
Authors Comments:LJM it originally came with a zero degree convex edge which I found was a bit too fine and subject to chipping and rolling; I love the 17 degree angle razor sharp and tough
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Fred Perrin Street Beat 3.5 inches 5/32th of an inch VG-10, 59 17 degrees per side ceramics and strops 5 and 3.5 diamond paste Top B-1 EDC / Tactical fixed blade
 
Authors Comments:Fred Perrin is an ex-special forces France knife designer and he has made a scary little knife here. It is full flat ground, so needs special attention when mounting. I use chamois to fill the voids.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Leo James Mitchell
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Fallkniven S1 130 mm 5 mm VG-10 59 22 1000# Diamond Bottom C survival / bushcraft
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: jolut
Rating:
Rating:
Rating:
Rating:
Rating:


Page 10 of 18 Results 91 - 100 of 172