Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Spyderco Delica 4 2.88 0.093 ZDP-189 64 17, Mirco 20 3.5 um @19 Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: TPeters
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Stretch 2 CF 3.5" .125" ZDP-189 64HRC 15 3.5um Bottom... B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kershaw Blur 3.3125" .125" ZDP-189 64HRC 17 1um Bottom. A.5 EDC (Every day carry)
 
Authors Comments:After several months of experimenting, I've settled on 17 degrees for this knife. It gives great performance and holds its edge well. I keep it pretty polished for show and sometimes it's a little too smooth for the work it does so I might put a slightly toothy, almost invisible micro-bevel on it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Peter Altenbach Chefs Knife 10" 3mm X45CrMoV15 ? 20 2k Chosera Bottom E Chopping and Slicing
 
Authors Comments:I've had this knife for over 24 years and have used it regularly. The steel isn't spectacular and really doesn't hold up well below 20 degrees. I like the shoulders polished and the edge just a little toothy. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
J. A. Henckels Professional "S" 31020-100 Paring 4" 1.5mm X50CrMoV15 ? 20 3.5um Top B Paring
 
Authors Comments:The steel is not spectacular and while I'd like to go lower, it only really holds up at 20 degrees and up. I like to keep it fairly polished since I mostly push-cut with it. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
J. A. Henckels Professional "S" 31021-160 Chef 6" 3mm X50CrMoV15 ? 20 2k Chosera Bottom C Chopping and Slicing
 
Authors Comments:Not the greatest steel, doesn't hold its edge well, especially below 20 degrees. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Tojiro YJFF-CH160 160mm ? ? ?
 
Authors Comments:this is all iknow and any help you guys might have would be great
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Smith SWBLOP3 3.4 ? 4034 ? 20 3.5 mu ? B ever day use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MelvinSharp
Rating:
Rating:
Rating:
Rating:
Rating:
Protech Runt J4 2 inches 0.11 inches 154 CM ? Mfg angle of ~ 18 maintained ? Upper holes Butted to handle EDC
 
Authors Comments:Not a lot of blade here. Butted blade up against handle in vise. Tried to clamp with edge basically parallel and used upper holes. Factory bevels not quite equal on both sides, so started with 1000 and worked up thru ceramics in order.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Mora Frost Exclusive 345 125 mm 3 mm ? ? 22 1000# Diamond Top C Outdoor / fishing
 
Authors Comments:This is a knife I have been using since the late '70.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: jolut
Rating:
Rating:
Rating:
Rating:
Rating:


Page 11 of 17 Results 101 - 110 of 168