Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Voyager (Medium Tanto) 3" 3 mm AUS 8A HRC 57-59 19 3.5um 1st A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Chris Reeve Small Sebenza 2.94in 0.125in S35VN 58-59 RC 22 Degrees 3.5um Top A 1/2 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Buck 119BKS-B 6 ? 440C ? 20 3.5um Bottom C Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
Buck 119BKS-B 6 ? 440C ? 20 3.5um Bottom C Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
Shun DM0501 Ken Onion Utility Knife 5" ? VG10 61 16 3.5um Top C Cooking - general purpose kitchen utility
 
Authors Comments:Used the top holes but only rested the spine on the prong closest to me and rotated the blade to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
16 Degrees, Top Holes, Align=C, Finish=3.5um

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
9
Rating:
Rating:
Rating:
Rating:
Shun DM-0516 Ken Onion Paring Knife 3" ? VG10 61 16 3.5um Top B Cooking, paring
 
Authors Comments:Set spine on the pin closest to me and then rotated the edge to horizontal.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
Shun DM-0500 8" ? VG10 61 16 3.5um Bottom D Chopping, slicing, general cooking
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Twitch II 2.68" .1" AUS-8 HRC 57-58 22 3.5u Top A.5
 
Authors Comments:My progression was 800 to 1600 ceramics. Then 14, 10, 5, 3.5u strops. 100 strokes with each strop then would flip strops end for end at 50 so the whole strop would get worn evenly
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Twitch XL 3.25 0.13 AUS-8 RC 57-58 22 3.5u Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: SleeplessJunkie
Rating:
Rating:
Rating:
Rating:
Rating:


Page 7 of 18 Results 61 - 70 of 172