Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
IKEA Pairing knife 100 mm 1.35 mm Cheap stainelss 54 22 0.6 um micro fine T B.0 Fruit and smaller veggies in the kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Anders Petter Fillet knife 150 mm 1.6 mm Molybdenum stainless 57 21 0.6 um micro fine T C.0 Filleting of fish in kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Kongsberg Norway Mora like utility knife 100 mm 2.0 mm Unspec. HiCarbon 56 22 0.6 um micro fine T A.5 Chopping, boxes, rope, branches, prying.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Leatherman Super Tool (original) 3" n/a n/a (cheap) n/a 22 1000# then 5-3.5 leather strops spine only in vice A .5 EDC
 
Authors Comments:set blade high in vice, only the square part of spine in vice
Angle/Finish Tried with Ratings
Setting 1:
lower in vice with depth key at high

Setting 2:
22 deg, 1000#, 3.5u strops, depth higher, see comm

Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
4
Rating:
6
Rating:
Rating:
Rating:
Cutco 2 3/4" paring Item # 1720 2.75 - 440A - 17 1000# then 5-3.5 leather strops spine only in vice A.5 kitchen, general use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
A.5, 17 deg.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
7
Rating:
Rating:
Rating:
Rating:
Spyderco Leaf Storm 2.125" .125" CPMS30V unknown 15 1000 Grit Short Short, very short Pocket knife
 
Authors Comments:NA
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
SOG Spec Elite 1 3.75" 1/8" Seki Japan VG10 60-61 HRC 16 degrees 3.5micron shallow dept C thumb knob onClamp EDC light to moderate use
 
Authors Comments:difficult to set up in Clamp, recommend removing thumb knob for sharpening entire blade length
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Buck Metro (759) 1" ? 420HC ? 17 1000# daniel, a few light cleanup passes with 5um leather See comments A.5 EDC
 
Authors Comments:Clamp on the bottle opener ring, the aluminum body section will control depth. Align to A.5 and level out the little blade with the clamp as best you can! Works surprisingly well.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Fallkniven A1 6.3 0.24 VG-10 59 15 1600 Low B 0.75
 
Authors Comments:I put a 15 degrees microbevel on top of a 13 degrees convex edge
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Boker Plus Toucan multi tool neck knife 1.02 inches / 2.6cm 0.2 inches / 5mm 440c 58 HRC 22* factory angle 0.6 mic ceramic Level @ grind line 0.8 A Neck knife multi tool
 
Authors Comments:Depth level with grind line
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:


Page 11 of 17