Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Boker Plus Toucan multi tool neck knife 1.02 inches / 2.6cm 0.2 inches / 5mm 440c 58 HRC 22* factory angle 0.6 mic ceramic Level @ grind line 0.8 A Neck knife multi tool
 
Authors Comments:Depth level with grind line
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Fallkniven A1 6.3 0.24 VG-10 59 15 1600 Low B 0.75
 
Authors Comments:I put a 15 degrees microbevel on top of a 13 degrees convex edge
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Lion Steel Opera 3.54 NA D2 NA NA Satin NA NA EDC
 
Authors Comments:Can anyone fill in the missing data for me? Thanks.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: mikemci
Rating:
Rating:
Rating:
Rating:
Rating:
Buck Metro (759) 1" ? 420HC ? 17 1000# daniel, a few light cleanup passes with 5um leather See comments A.5 EDC
 
Authors Comments:Clamp on the bottle opener ring, the aluminum body section will control depth. Align to A.5 and level out the little blade with the clamp as best you can! Works surprisingly well.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Spec Elite 1 3.75" 1/8" Seki Japan VG10 60-61 HRC 16 degrees 3.5micron shallow dept C thumb knob onClamp EDC light to moderate use
 
Authors Comments:difficult to set up in Clamp, recommend removing thumb knob for sharpening entire blade length
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: guest
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Leaf Storm 2.125" .125" CPMS30V unknown 15 1000 Grit Short Short, very short Pocket knife
 
Authors Comments:NA
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Leatherman Super Tool (original) 3" n/a n/a (cheap) n/a 22 1000# then 5-3.5 leather strops spine only in vice A .5 EDC
 
Authors Comments:set blade high in vice, only the square part of spine in vice
Angle/Finish Tried with Ratings
Setting 1:
lower in vice with depth key at high

Setting 2:
22 deg, 1000#, 3.5u strops, depth higher, see comm

Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
4
Rating:
6
Rating:
Rating:
Rating:
Cutco 2 3/4" paring Item # 1720 2.75 - 440A - 17 1000# then 5-3.5 leather strops spine only in vice A.5 kitchen, general use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
A.5, 17 deg.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
7
Rating:
Rating:
Rating:
Rating:
Blackfield R.P.K. Crossfire 90mm 2.5mm 440B HRC 58 21 Micro fine ceramics (0.6 um) T B.0 Rescue knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:
Mora Utility knife 100 mm 1.9 mm Hi-Carbon steel 57 22 0.6 um micro fine T A.5 Dirty work around the house, cables, boxes...
 
Authors Comments:Very difficult to really reach in to the blade close to the handle due to the quillon / hilt (alomst need a re-clamp).
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: johpe
Rating:
Rating:
Rating:
Rating:
Rating:


Page 7 of 18 Results 61 - 70 of 172