Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
CRKT M21-14SF 3.875 inches 0.14 inches AUS 8 58-59 18.5 5 micron Bottom A 0.5 Put a usable polished sharp edge in place.
 
Authors Comments:I will test the durability and usability of this edge in the coming weeks.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
10
Rating:
Rating:
Rating:
Rating:
Fallkniven SK-1 3.88 inches .18 inches 3G laminated powder 62 16 degrees ceramics and strops with 5 and 3.5 micron pastes Top B.3 Bushcraft
 
Authors Comments:LJM
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Buck Zipper. 191 4 1/8 inch 0.14 inch 420HC ? 18/side. Leather strop 1mic Upper B.5 Skinning fixed blade
 
Authors Comments:Buck states factory angles are 13-16/side. This was closer to 18/side. Diamond 400 - 1000. Ceramic 1.4 then leather strops as noted in finish.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Wicked Edge Hunting Knife 4 in. .125 in. AUS-8 Unk. 18 deg. 14m Leather Bottom B.5 Hunting / Camping
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Fallkniven TK-1 4 inches .18 inches 3G laminated powder 62 21 degrees ceramics and strops with 5 and 3.5 micron pastes Top B.4 bushcraft
 
Authors Comments: LJM
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Heckles Professional S paring 4 inches ? "High carb stainless ? 17.8 ? Above upper holes B Kitchen
 
Authors Comments:Diamond: 600 to 1000. Ceramic:1200 to 0.6 mic. Final: naniwa 8k
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Oxo Good grips paring 4 inches ? Stainless ? 18 1000 diamond Above upper holes B General kitchen duties
 
Authors Comments:4/2/13 trying 2* bevel at 20* with 1000 diamond
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Military CF 4" .156" S90V unknown 15 3.5um Bottom. B.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Cold Steel Black Sable 4" .125" San Mai III 58 HRC 18 primary bevel, 19 degree micro bevel 1600# Top B.5 EDC
 
Authors Comments:I originally created the bevels at 18 degrees and polished them to .5 microns before adding a micro-bevel at 19 degrees with the 1600# ceramic stones to give a mirrored bevel and slightly reduced shoulder while making the actual edge a little wider and giving it some micro teeth.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1


Page 13 of 17