Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Spyderco Paramilitary 2 CF 3.44 1.41 S90V 62 19 L - 20 R 3.5 um Bottom A.5
 
Authors Comments:Maintains the manufactures angle
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Police 4.125 .125 VG-10 Unknown 19 1000, 6 micron strop , 3 micron strop Top B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kershaw ZT 0560 3.75" .1625" Elmax 60-62 HRC 19 Micro-Fine .6 Bottom B EDC
 
Authors Comments:So far I love the knife and the settings I've chosen. It's extremely aggressive and very durable.
Angle/Finish Tried with Ratings
Setting 1:
19 degrees, AC verified. .6 Micro-Fine Finish.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT Folts Minimalist 127mm 2.1mm 5Cr15MoV 57 RC 19 5u Lap Top 30mm Tip to CL/Vise EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
reprofile to 19, finish 1000 diamond

Setting 2:
reprofile to 19, then finish at 0.3u

Setting 3:
0.3 lap then fine strop .5u on leather

Setting 4:


Setting 5:


Author: BassLakeDan
Rating:
5
Rating:
8
Rating:
6
Rating:
Rating:
Gerber Mini Covert 3" 0.110" 154CM Not listed 19 1k diamond for duty/carry, but takes well to full out mirror polish too! Top A.5 EDC
 
Authors Comments:In matching the factory bevel, an even 19 degrees per side ends up 18 on the left arm and 20 on the right arm. Thus far the 19 degree edge has held up very well, as a 154CM should!
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Voyager (Medium Tanto) 3" 3 mm AUS 8A HRC 57-59 19 3.5um 1st A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Buck 425 1 7/8 ? 420HC 58 19 .6 Micron Ceramic Above TOP A .25 Pocket
 
Authors Comments:Make sure you have it above the top Depth holes or you will be hitting your vise.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JacobNoes
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JG
Rating:
10
Rating:
Rating:
Rating:
Rating:
Buck Zipper. 191 4 1/8 inch 0.14 inch 420HC ? 18/side. Leather strop 1mic Upper B.5 Skinning fixed blade
 
Authors Comments:Buck states factory angles are 13-16/side. This was closer to 18/side. Diamond 400 - 1000. Ceramic 1.4 then leather strops as noted in finish.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Fällkniven NL5 IDUN 100 mm 5 mm Lam.VG10 59 HRC 18/19/20 1000# Diamond / 1600# Ceramic | blending 14/10 strops, 1/,5 strops top B bushcraft
 
Authors Comments:I have now tested the edge with a lot of whittling, edge shaved but not easily, stropping on 19 degrees took it back to a good razoredge.. Tony Pettersen "EDIT OUT - i think someone have placed their comment on this knife by mistake, idun is no lockback - EDIT OUT"
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1


Page 9 of 17 Results 81 - 90 of 168