Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Strider SnG 3.5 .165 S30V Unknown 24 Degree Bevel with 26 Degree Stropping (Widen arms for Stropping) 600 Grit Bevel, 10 Micron Stropping Top. B.8 Tactical
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Cold Steel Master Tanto 6" .1875" VG1 San Mai III 56-58RHC 25 .5um Bottom B.5 Tactical
 
Authors Comments:I inherited this knife from my step father who carried it overseas for many years. It had been hand sharpened for years so it's hard to know what the original angle was. Reprofiling it took some time but it finished up nicely and took a super polish.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: wickededge
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Strider GW/AR152 8" .250 S30V unknown 25 3.5 micron Bottom C OCONUS deployment
 
Authors Comments:I'll check the hardness when I see the knife again
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Strider PT 2.87 0.125 S30V Unknown 30 3.5um Bottom. A.25
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
CRKT M16-13T 3.5" 0.110" AUS8 58-59 Asymmetrical grind (70/30), I used left 20, right 15 to get close and finished the profile that way 1k diamond -> 5um strop for finish and touchup Unique (see comment) B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Gerber Remix 2.9" .115 mystery Stainless unk L 16, R 17 Micro Fine Ceramic Stones .6micron top A .5 Utility beater/Test bed
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
SOG Vulcan 3.25 .157 VG-10 59-60 l 17/r 21 .05 strop top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT Ripple 3.125 .107 8CR14MoV 59-60 l 20/r 20 .05 strop top a5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
Zero Tolerance 0560/0561 3.75 in 0.157 Elmax 60 left 25/right 26 3.5 micro leather bottom B.5 EDC
 
Authors Comments:Not the sharpest thing in the world but will keep that edge for quite some time.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JosephMurray
Rating:
Rating:
Rating:
Rating:
Rating:
Protech Runt J4 2 inches 0.11 inches 154 CM ? Mfg angle of ~ 18 maintained ? Upper holes Butted to handle EDC
 
Authors Comments:Not a lot of blade here. Butted blade up against handle in vise. Tried to clamp with edge basically parallel and used upper holes. Factory bevels not quite equal on both sides, so started with 1000 and worked up thru ceramics in order.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:


Page 17 of 18 Results 161 - 170 of 172