Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Buck Vantage Pro 3.25" 0.120" S30V 59 18 1k diamond, with strops for touch up Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: ApexGS
Rating:
Rating:
Rating:
Rating:
Rating:
Kabar K2 Chinchete 3.25" 0.15" 3CR13 50-52 18 3.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Cold Steel Twist Master 3.5 ? Carbon V ? 17.3 8k Naniwa super stone Upper holes B EDC
 
Authors Comments:Diamond 400-1000. Ceramic 1200-0.6. Naniwa 8k. Bought several of these as close outs/ factory 2nds About 20 years ago. Takes a nice edge easily and keeps it well. Rusts easily.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Oxo Good grips paring 4 inches ? Stainless ? 18 1000 diamond Above upper holes B General kitchen duties
 
Authors Comments:4/2/13 trying 2* bevel at 20* with 1000 diamond
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Persistence 2.75" 0.125" 8Cr13MoV HRC 58-59 15 0.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: MartinL1
Rating:
Rating:
Rating:
Rating:
Rating:
Furi Gustogrip FUR812 paring 4" 0.075 CrMoV 56 23 diamonds to 1000/strop to .05 top B Kitchen
 
Authors Comments:This finish leaves a refined but toothy edge that seems to work better.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
Furi Lil Edgy Santoku 5" .105 CrMoV 56 23 diamonds to 1000/strop to .05 top B Kitchen
 
Authors Comments:This finish leaves a refined but toothy edge that seems to work well for kitchen duty..
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: xuzme720
Rating:
Rating:
Rating:
Rating:
Rating:
Chris Reeve Small Sebenza 21 2.94" .125" S35VN Stainless Stee 58-59 RC 18 deg. with 19,20 deg. Micro bevel for convex 18 Deg finished with Roo Strop .125 CBN and blank Top Holes B EDC
 
Authors Comments:All angles set with Angle Cube, rechecked on each stone. Re-created 18 Degree bevel with Diamond 400 -1000, Ceramic 1200/1600 then 5000/10000 Chosera. With 5/10k Chosera reset angle to 20 , 19 then back to 18deg. to define convex. Continued with Balsa 20, 19 then 18deg. with .5 Microne paste Completed at 18deg finish with Roo with .125 Cubic Boron then blank Roo with a mist of alcohol. Shaving sharp and developing a nice mirror polish edge. Maintenance additional careful stropping will r
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: JamesBell
Rating:
Rating:
Rating:
Rating:
Rating:
CRKT Onion-Shenanigan #K470KKP 3.25 inch 0.119 inch / 3.0mm Acuto 59-60 HRC 20* 0.6 ceramic Upper holes B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Mikedoh
Rating:
Rating:
Rating:
Rating:
Rating:


Page 10 of 17 Results 91 - 100 of 168