Manufacturer Model Blade Length Thickness Steel Hardness Recommended Angle Recommended Finish Depth AlignmentIntent
Global GS-5 140 mm 2 mm CROMOVA 18 SS 56-58 20 1000# diamond Top B .5 Kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: jolut
Rating:
Rating:
Rating:
Rating:
Rating:
Cutco 4" Paring Knife, #2120 4" n/a 440A n/a 17 0.5 strops Top B 1/4 general kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
B 1/4, 17 deg.

Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author: Geocyclist
Rating:
Rating:
Rating:
Rating:
Rating:
Spyderco Superleaf CF 3.438" .156" VG-10 unknown 15 3.5um Bottom. B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Stretch 2 CF 3.5" .125" ZDP-189 64HRC 15 3.5um Bottom... B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Spyderco Police 4.125 .125 VG-10 Unknown 19 1000, 6 micron strop , 3 micron strop Top B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Bradely Alias ii 2.95 .120 S30V Unknown 18 1000 Stones, 6 micron strop , 3 micron strop Top B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Fällkniven NL5 IDUN 100 mm 5 mm Lam.VG10 59 HRC 18/19/20 1000# Diamond / 1600# Ceramic | blending 14/10 strops, 1/,5 strops top B bushcraft
 
Authors Comments:I have now tested the edge with a lot of whittling, edge shaved but not easily, stropping on 19 degrees took it back to a good razoredge.. Tony Pettersen "EDIT OUT - i think someone have placed their comment on this knife by mistake, idun is no lockback - EDIT OUT"
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Fallkniven PXL Folder 3.4 inches .138 3 G Powder steel lam 62 16 ceramics and strops Top B EDC
 
Authors Comments:This is my favourite EDC knife. It is pretty and it is sharp in the extreme. I give this knife a five out of five for looks, usefullness and strength.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
J. A. Henckels Professional "S" 31020-100 Paring 4" 1.5mm X50CrMoV15 ? 20 3.5um Top B Paring
 
Authors Comments:The steel is not spectacular and while I'd like to go lower, it only really holds up at 20 degrees and up. I like to keep it fairly polished since I mostly push-cut with it. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:


Setting 2:


Setting 3:


Setting 4:


Setting 5:


Author:
Rating:
1
Rating:
1
Rating:
1
Rating:
1
Rating:
1


Page 8 of 18 Results 71 - 80 of 172