Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Kai Shun DM-0716 4 inch / 100 mm 1.5 mm VG-MAX 61 16 0.5 um leather strop T B.0 Kitchen paring knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
J. A. Henckels Professional "S" 31020-100 Paring 4" 1.5mm X50CrMoV15 ? 20 3.5um Top B Paring
 
Authors Comments:The steel is not spectacular and while I'd like to go lower, it only really holds up at 20 degrees and up. I like to keep it fairly polished since I mostly push-cut with it. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Anders Petter Fillet knife 150 mm 1.6 mm Molybdenum stainless 57 21 0.6 um micro fine T C.0 Filleting of fish in kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Tamahagane 3-ply TK-1107 Petty knife 150 mm 1.6 mm VG5 59 15 0.6 um micro fine ceramics T B.5 Kitchen use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Tamahagane 3-ply TK-1108 paring knife 120 mm 1.6 mm VG5 59 15 0.6 um micro fine ceramics T B.0 Kitchen use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Tamahagane 3-ply TK-1120 Filleting knife 160 1.6 mm VG5 clad with SUS410 HRC 59 15 0.5 um leather strop T C.0 Fish work in kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kai Shun DM-0710 Filleting knife 150 mm 1.7 mm VG-10 HRC 61 16 0.5 um leather strop T C.0 Handling fish in the kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Mora Utility knife 100 mm 1.9 mm Hi-Carbon steel 57 22 0.6 um micro fine T A.5 Dirty work around the house, cables, boxes...
 
Authors Comments:Very difficult to really reach in to the blade close to the handle due to the quillon / hilt (alomst need a re-clamp).
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Gayle Bradley 3.5 1/8 CPM M4 I think about 62 RC 15 1 micron boron carbide(HandAmercian) on balsa Top B EDC
 
Authors Comments:I like this steel. It takes a variety of finishes well but for EDC I like a congress 400 or the 1000 diamonds followed by 1 micron boron carbide paste on balsa the best. This seems to be about where hair whittling starts but it still has some bite. Hope you like it as much as I do.
Angle/Finish Tried with Ratings
Setting 1:
17 degrees 1000 diamond 3.5 paste on balsa
Setting 2:
15 degrees 1000 diamond 1 BC on balsa
Setting 3:
15 degrees 400 congress 1 BC on balsa
Setting 4:
15 degrees all the way to .125 CBN on roo
Setting 5:


 Author: guest
Rating:
6		 Rating:
7		 Rating:
9		 Rating:
8		 Rating:
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 13 of 20