Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Reinhard Müller MSP Linerlock 85 mm 3,7 mm CPMS90V HRC 58 18 0.5 um paste on leather strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Leaf Storm 2.125" .125" CPMS30V unknown 15 1000 Grit Short Short, very short Pocket knife
 
Authors Comments:NA
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Native 5 3" .125" CPM S35VN HRC 59-62 17 0.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Gayle Bradley 3.5 1/8 CPM M4 I think about 62 RC 15 1 micron boron carbide(HandAmercian) on balsa Top B EDC
 
Authors Comments:I like this steel. It takes a variety of finishes well but for EDC I like a congress 400 or the 1000 diamonds followed by 1 micron boron carbide paste on balsa the best. This seems to be about where hair whittling starts but it still has some bite. Hope you like it as much as I do.
Angle/Finish Tried with Ratings
Setting 1:
17 degrees 1000 diamond 3.5 paste on balsa
Setting 2:
15 degrees 1000 diamond 1 BC on balsa
Setting 3:
15 degrees 400 congress 1 BC on balsa
Setting 4:
15 degrees all the way to .125 CBN on roo
Setting 5:


 Author: guest
Rating:
6		 Rating:
7		 Rating:
9		 Rating:
8		 Rating:
Benchmade 525 Presidio M4 LE (525BK-1101) 3 0.12 CPM M4 59-61 15 0.5 strops Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
15 deg; A.5; 1000#, 12k chosera, 0.5 stops
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 558 DLC M4 - Ritter Mini Griptilian 2.9 0.1 CPM M4 59-61 15 10k chosera, 0.5 strop Top A.75 EDC
 
Authors Comments:Had to go with top position to get clearance for 15 deg. A.75 got the bevel pretty even, just a little more on the belly and tip, but looks good. Stropped with both balsa and leather at 15 deg.
Angle/Finish Tried with Ratings
Setting 1:
15 deg, 10k Chosear, balsa and leather at 15 deg.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 551 1303 3.4 .115 CPM M4 59-61 15 1k Chosera, 3.5 Strops Top A.75 EDC
 
Authors Comments:Needed top depth at 15 deg. Might try alignment "B" next time to get bevel more even (A.75 is a little bevel at tip)
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
IKEA Chef knife 200 mm 2.2.mm Cheap stainless 54 22 0.6 um micro fine B D.0 Doing dirty work in the kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
IKEA Utility knife 120 mm 1.35 mm Cheap stainless 54 22 0.6 um micro fine T B.0 Onion and larger veggies in the kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
IKEA Pairing knife 100 mm 1.35 mm Cheap stainelss 54 22 0.6 um micro fine T B.0 Fruit and smaller veggies in the kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 11 of 20