Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Spyderco Superleaf CF 3.438" .156" VG-10 unknown 15 3.5um Bottom. B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Leatherman Super Tool (original) 3" n/a n/a (cheap) n/a 22 1000# then 5-3.5 leather strops spine only in vice A .5 EDC
 
Authors Comments:set blade high in vice, only the square part of spine in vice
Angle/Finish Tried with Ratings
Setting 1:
lower in vice with depth key at high
Setting 2:
22 deg, 1000#, 3.5u strops, depth higher, see comm
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
4		 Rating:
6		 Rating:
 Rating:
 Rating:
Fontignac Sujihiki 27 cm ? VG10 55 18 Chosera 10K Bottom C 0.5 ?
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Bark River STS-5 5.5 inches .270 inches 154 CM Stainless Ste 58 16 degrees ceramics and strops with 5 and 3.5 micron pastes bottom C Tactical/Survival
 
Authors Comments:Basically a belly to belly fighter but can be used as a survival knife. LJM
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Stretch 2 CF 3.5" .125" ZDP-189 64HRC 15 3.5um Bottom... B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Knives of Alaska Steelheader 5.75 ? 440C 58-60 18 1000# Top D Fillet Knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Spec Elite 1 3.75" 1/8" Seki Japan VG10 60-61 HRC 16 degrees 3.5micron shallow dept C thumb knob onClamp EDC light to moderate use
 
Authors Comments:difficult to set up in Clamp, recommend removing thumb knob for sharpening entire blade length
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Strider SnG 3.5 .165 S30V Unknown 24 Degree Bevel with 26 Degree Stropping (Widen arms for Stropping) 600 Grit Bevel, 10 Micron Stropping Top. B.8 Tactical
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Chris Reeve Small Sebenza 21 2.94" .125" S35VN Stainless Stee 58-59 RC 18 deg. with 19,20 deg. Micro bevel for convex 18 Deg finished with Roo Strop .125 CBN and blank Top Holes B EDC
 
Authors Comments:All angles set with Angle Cube, rechecked on each stone. Re-created 18 Degree bevel with Diamond 400 -1000, Ceramic 1200/1600 then 5000/10000 Chosera. With 5/10k Chosera reset angle to 20 , 19 then back to 18deg. to define convex. Continued with Balsa 20, 19 then 18deg. with .5 Microne paste Completed at 18deg finish with Roo with .125 Cubic Boron then blank Roo with a mist of alcohol. Shaving sharp and developing a nice mirror polish edge. Maintenance additional careful stropping will r
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JamesBell
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Chris Reeve Small Sebenza 2.94in 0.125in S35VN 58-59 RC 22 Degrees 3.5um Top A 1/2 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 3 of 20