Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Tojiro ITK 120 mm petty 4.72 . White #2 60 15 Chosera 10K Bottom B 0.5 .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Wicked Edge Hunting Knife 4 in. .125 in. AUS-8 Unk. 18 deg. 14m Leather Bottom B.5 Hunting / Camping
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
DPX Gear HEST 1.0 3.67 inches .197 inches D2 Tool Steel 58-59 21 degrees per side ceramics and strops 5 and 3.5 diamond paste Top B-1 Survival folder/EDC
 
Authors Comments: This has been a controversial knife. The model 1 in some cases had weaknesses but luckily for me my cop was fine. A very sturdy knife with a D-2 tool steel blade that sharpens up incredibly and retains the edge well. It is one of my EDC knives.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Leo James Mitchell
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Strider GW/AR152 8" .250 S30V unknown 25 3.5 micron Bottom C OCONUS deployment
 
Authors Comments:I'll check the hardness when I see the knife again
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Furi Gustogrip FUR812 paring 4" 0.075 CrMoV 56 23 diamonds to 1000/strop to .05 top B Kitchen
 
Authors Comments:This finish leaves a refined but toothy edge that seems to work better.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Bark River Gunny carbon steel blade 3.775 inche .154 inches A-2 tool steel 58 18 degrees ceramics and strops 5 and 3.5 diamond paste Top B.1 bushcraft
 
Authors Comments:LJM A smaller version of the Bravo1...very good gripping handle for four fingers
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Global GS-5 140 mm 2 mm CROMOVA 18 SS 56-58 20 1000# diamond Top B .5 Kitchen
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Oxo Good grips paring 4 inches ? Stainless ? 18 1000 diamond Above upper holes B General kitchen duties
 
Authors Comments:4/2/13 trying 2* bevel at 20* with 1000 diamond
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Gayle Bradley 3.5 1/8 CPM M4 I think about 62 RC 15 1 micron boron carbide(HandAmercian) on balsa Top B EDC
 
Authors Comments:I like this steel. It takes a variety of finishes well but for EDC I like a congress 400 or the 1000 diamonds followed by 1 micron boron carbide paste on balsa the best. This seems to be about where hair whittling starts but it still has some bite. Hope you like it as much as I do.
Angle/Finish Tried with Ratings
Setting 1:
17 degrees 1000 diamond 3.5 paste on balsa
Setting 2:
15 degrees 1000 diamond 1 BC on balsa
Setting 3:
15 degrees 400 congress 1 BC on balsa
Setting 4:
15 degrees all the way to .125 CBN on roo
Setting 5:


 Author: guest
Rating:
6		 Rating:
7		 Rating:
9		 Rating:
8		 Rating:
Mora Frost Exclusive 345 125 mm 3 mm ? ? 22 1000# Diamond Top C Outdoor / fishing
 
Authors Comments:This is a knife I have been using since the late '70.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 11 of 20