Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Wusthof Classic 10" Slicer 10" .110 X50CrMo14 56-57 RHC 20 1k-1.6k Top C General purpose kitchen utility, cuts lots of vegg
 
Authors Comments:I'd love to go more acute than 20 degrees but the edge just won't hold long enough. I keep it just a little toothy to compensate and it performs well. This is my wife's favorite knife and she uses and abuses constantly.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Emerson CQC-8 100 mm 3 mm 154CM? 57-59 23 1000# Diamond Bottom B Hard use survival / bushcraft
 
Authors Comments:This folder is from 2004 without wave. I have a V-grind on this one.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Cryo 1555TIX 2.75 inch ? 8Cr13MoV ? 22* per side Leather /c 0.5 mic diamond Upper A.5 Sons 1st interesting knives
 
Authors Comments:Diamond 800, 1000. Ceramic 1.4, 1200,1600. Naniwa 8k. Ceramic 0.6. Leather strops 1
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Delica 4 2.875" 2.5mm VG-10 N/A 20 degrees 3.5 micron strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Delica 4 2.88 0.093 ZDP-189 64 17, Mirco 20 3.5 um @19 Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0500 8" ? VG10 61 16 3.5um Bottom D Chopping, slicing, general cooking
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0516 Ken Onion Paring Knife 3" ? VG10 61 16 3.5um Top B Cooking, paring
 
Authors Comments:Set spine on the pin closest to me and then rotated the edge to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kai Shun DM-0706 200mm 1mm VG-10 61 ± 1 HRC 16 0.5 um leather strop Bottom D.0 Misc kitchen use
 
Authors Comments:Refined the factory (16 degrees) edge, got scary sharp and passed HHT.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM0501 Ken Onion Utility Knife 5" ? VG10 61 16 3.5um Top C Cooking - general purpose kitchen utility
 
Authors Comments:Used the top holes but only rested the spine on the prong closest to me and rotated the blade to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
16 Degrees, Top Holes, Align=C, Finish=3.5um
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
9		 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Dragonfly 58 mm 2.5 mm VG-10 HRC 59-61 15 Micro fine ceramic stones (0.6 um) Top 1 or 2 matches A.0 Light EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 6 of 19