Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Gerber EZ Out 3 .1 high carbon stainles n/a 17.5 1000# then 5-3.5 leather strops Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
1000# 17.5 deg., stop @ 16.5
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 556 Mini Griptilian 2.9 0.10 154 cm 58-61 17.5 10k chosera, 0.5 strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
17.5 deg.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck Metro (759) 1" ? 420HC ? 17 1000# diamond, a few light cleanup passes with 5um leather See comments A.5 EDC
 
Authors Comments:Clamp on the bottle opener ring, the aluminum body section will control depth. Align to A.5 and level out the little blade with the clamp as best you can! Works surprisingly well.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 525 Presidio M4 LE (525BK-1101) 3 0.12 CPM M4 59-61 15 0.5 strops Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
15 deg; A.5; 1000#, 12k chosera, 0.5 stops
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 940 3.4 0.12 S30V 58-60 15 10k chosera, 0.5 strop Top B.5 (thumb studs) EDC
 
Authors Comments:Aligned thumb studs to vice, about B.5. See photos in URL.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 558 DLC M4 - Ritter Mini Griptilian 2.9 0.1 CPM M4 59-61 15 10k chosera, 0.5 strop Top A.75 EDC
 
Authors Comments:Had to go with top position to get clearance for 15 deg. A.75 got the bevel pretty even, just a little more on the belly and tip, but looks good. Stropped with both balsa and leather at 15 deg.
Angle/Finish Tried with Ratings
Setting 1:
15 deg, 10k Chosear, balsa and leather at 15 deg.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
Zero Tolerance zt0350 3 1/4 .121 S30V Unk 20 deg. MicroFine-Fine Bottom B EDC
 
Authors Comments:MicroFine finish after 600g diamond stone
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: cbwx34
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Chris Reeve Small Sebenza 2.94in 0.125in S35VN 58-59 RC 22 Degrees 3.5um Top A 1/2 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Twitch XL 3.25 0.13 AUS-8 RC 57-58 22 3.5u Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: SleeplessJunkie
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JG
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 12 of 20