Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Wusthof Santoku 4176 Classic Ikon 6.5" - X50CrMoV15 - 15 1600 Ceramic Bottom C.5 Cooking
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM0501 Ken Onion Utility Knife 5" ? VG10 61 16 3.5um Top C Cooking - general purpose kitchen utility
 
Authors Comments:Used the top holes but only rested the spine on the prong closest to me and rotated the blade to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
16 Degrees, Top Holes, Align=C, Finish=3.5um
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
9		 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0516 Ken Onion Paring Knife 3" ? VG10 61 16 3.5um Top B Cooking, paring
 
Authors Comments:Set spine on the pin closest to me and then rotated the edge to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Mora Utility knife 100 mm 1.9 mm Hi-Carbon steel 57 22 0.6 um micro fine T A.5 Dirty work around the house, cables, boxes...
 
Authors Comments:Very difficult to really reach in to the blade close to the handle due to the quillon / hilt (alomst need a re-clamp).
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
IKEA Chef knife 200 mm 2.2.mm Cheap stainless 54 22 0.6 um micro fine B D.0 Doing dirty work in the kitchen.
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT 4102 Michael Walker BladeLock II 2.875" Unknown AUS-4 Unknown 15 1600# Ceramic Top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Cold Steel Black Sable 4" .125" San Mai III 58 HRC 18 primary bevel, 19 degree micro bevel 1600# Top B.5 EDC
 
Authors Comments:I originally created the bevels at 18 degrees and polished them to .5 microns before adding a micro-bevel at 19 degrees with the 1600# ceramic stones to give a mirrored bevel and slightly reduced shoulder while making the actual edge a little wider and giving it some micro teeth.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Benchmade 9500 Mini-Auto Stryker 2.9" .1" 154CM 58-60HRC 20 3.5um Top A.5 EDC
 
Authors Comments:I've experimented with this knife many dozens of times over the years. My conclusion is that the steel won't hold well under 20 degrees. It's important to treat the blade in two sections to preserve the tanto geometry. I don't recommend a convex edge because of the loss of some of the precision cutting. It's an excellent EDC, especially for any utility work.
Angle/Finish Tried with Ratings
Setting 1:
22 Degrees / 1000# Diamond
Setting 2:
15 Degrees / 3.5um
Setting 3:
15 Degrees Primary, 17 Degrees Micro / 3.5um
Setting 4:
17 Degrees Primary, 20 Degrees Micro / 3.5um
Setting 5:


 Author: wickededge
Rating:
7		 Rating:
4		 Rating:
6		 Rating:
8		 Rating:
1
Spyderco Delica 4 2.875" 2.5mm VG-10 N/A 20 degrees 3.5 micron strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Fallkniven PXL Folder 3.4 inches .138 3 G Powder steel lam 62 16 ceramics and strops Top B EDC
 
Authors Comments:This is my favourite EDC knife. It is pretty and it is sharp in the extreme. I give this knife a five out of five for looks, usefullness and strength.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 7 of 19