Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Benchmade 551 Griptilian 3.45" .115" 154CM 58-60HRC 18 deg. w/ 20 deg. microbevel 3.5m on Balsa Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: cbwx34
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade Presidio Ultra 2.97" 0.115" 440C Stainless Stee 58-60HRC 15.25 (Measured) 5u Balsa, 3u and 1u 3M PSA Strips (50 passes per side) Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 522 Presidio Ultra - Pardue Axis Lock - Plain Edge 3.47 in .125 in 440C 58-60 rc 22 Degrees/Side 1000# Diamond / 1600# Ceramic / 10 Micron Strops Top A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Benchmade Emissary 470-1 3 inches 0.09 inches S30-v 58-60 HRC 21.75*. (? Factory?) Leather strop 0.5 mic Upper holes A.5 EDC
 
Authors Comments:Stone progression: diamond 1000; ceramic: 1.4, 1200, 1600. Superstone: 8k Naniwa. Ceramic 0.6. Leather strops /c 1 mic and 0.5 mic diamond paste. Tough steel. Not sure I'm settling on this.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Knives of Alaska Steelheader 5.75 ? 440C 58-60 18 1000# Top D Fillet Knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 940 3.4 0.12 S30V 58-60 15 10k chosera, 0.5 strop Top B.5 (thumb studs) EDC
 
Authors Comments:Aligned thumb studs to vice, about B.5. See photos in URL.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 940 3.4 ? S30V 58-60 17 Chosera 10K Bottom B 0.25 ?
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
?
Setting 2:
.
Setting 3:
..
Setting 4:
.
Setting 5:
.

 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Blur 4 ? S30V 58-60 10 Ceramic 1600 Bottom B .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Swamprat Ratmandu 4.75 0.1875 SR101 58-60 20 Diamond 1000 Bottom C .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 13 of 20