Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
CRKT Ripple 3.125 .107 8CR14MoV 59-60 l 20/r 20 .05 strop top a5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Vulcan 3.25 .157 VG-10 59-60 l 17/r 21 .05 strop top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Fällkniven NL5 IDUN 100 mm 5 mm Lam.VG10 59 HRC 18/19/20 1000# Diamond / 1600# Ceramic | blending 14/10 strops, 1/,5 strops top B bushcraft
 
Authors Comments:I have now tested the edge with a lot of whittling, edge shaved but not easily, stropping on 19 degrees took it back to a good razoredge.. Tony Pettersen "EDIT OUT - i think someone have placed their comment on this knife by mistake, idun is no lockback - EDIT OUT"
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Fallkniven A1 6.3 0.24 VG-10 59 15 1600 Low B 0.75
 
Authors Comments:I put a 15 degrees microbevel on top of a 13 degrees convex edge
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Bark River Bravo 1 4.250 inches .215 inches A-2 tool steel 59 17 degrees ceramics and strops with 5 and 3.5 micron pastes, I do a lot of stropping with green paste day to day and so I get a convexing to this edge over time top B-5 survival/bushcraft/tactical
 
Authors Comments:LJM it originally came with a zero degree convex edge which I found was a bit too fine and subject to chipping and rolling; I love the 17 degree angle razor sharp and tough
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Fred Perrin Street Beat 3.5 inches 5/32th of an inch VG-10, 59 17 degrees per side ceramics and strops 5 and 3.5 diamond paste Top B-1 EDC / Tactical fixed blade
 
Authors Comments:Fred Perrin is an ex-special forces France knife designer and he has made a scary little knife here. It is full flat ground, so needs special attention when mounting. I use chamois to fill the voids.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Leo James Mitchell
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Fallkniven S1 130 mm 5 mm VG-10 59 22 1000# Diamond Bottom C survival / bushcraft
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck Vantage Pro 3.25" 0.120" S30V 59 18 1k diamond, with strops for touch up Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Tanto 3.5 .115 154CM 59 18 .05 strop with a 1600 microbevel @22 top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
18 degrees to .05 strop
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
8		 Rating:
 Rating:
 Rating:
 Rating:
Tamahagane 3-ply TK-1107 Petty knife 150 mm 1.6 mm VG5 59 15 0.6 um micro fine ceramics T B.5 Kitchen use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 11 of 20