Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Benchmade 525 Mini-Presidio - Axis Lock - Plain Edge 2.97 in .115 in 154CM 58-59 rc 20-22 Degrees/Side 3.5um Top. A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Chris Reeve Large Sebenza 3.625" 0125" S35VN 58-59 RC 17 Deg. with 18 Deg. Microbevel 17 Deg. finished at 3.5u Strop Top Holes A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
17 degree main bevel 18,19,20,21 micro for convex

Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
9		 Rating:
 Rating:
 Rating:
 Rating:
Chris Reeve Small Sebenza 21 2.94" .125" S35VN Stainless Stee 58-59 RC 18 deg. with 19,20 deg. Micro bevel for convex 18 Deg finished with Roo Strop .125 CBN and blank Top Holes B EDC
 
Authors Comments:All angles set with Angle Cube, rechecked on each stone. Re-created 18 Degree bevel with Diamond 400 -1000, Ceramic 1200/1600 then 5000/10000 Chosera. With 5/10k Chosera reset angle to 20 , 19 then back to 18deg. to define convex. Continued with Balsa 20, 19 then 18deg. with .5 Microne paste Completed at 18deg finish with Roo with .125 Cubic Boron then blank Roo with a mist of alcohol. Shaving sharp and developing a nice mirror polish edge. Maintenance additional careful stropping will r
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JamesBell
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Chris Reeve Small Sebenza 2.94in 0.125in S35VN 58-59 RC 22 Degrees 3.5um Top A 1/2 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Knives of Alaska Steelheader 5.75 ? 440C 58-60 18 1000# Top D Fillet Knife
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 940 3.4 0.12 S30V 58-60 15 10k chosera, 0.5 strop Top B.5 (thumb studs) EDC
 
Authors Comments:Aligned thumb studs to vice, about B.5. See photos in URL.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 940 3.4 ? S30V 58-60 17 Chosera 10K Bottom B 0.25 ?
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
?
Setting 2:
.
Setting 3:
..
Setting 4:
.
Setting 5:
.

 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Blur 4 ? S30V 58-60 10 Ceramic 1600 Bottom B .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Swamprat Ratmandu 4.75 0.1875 SR101 58-60 20 Diamond 1000 Bottom C .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade Emissary 470-1 3 inches 0.09 inches S30-v 58-60 HRC 21.75*. (? Factory?) Leather strop 0.5 mic Upper holes A.5 EDC
 
Authors Comments:Stone progression: diamond 1000; ceramic: 1.4, 1200, 1600. Superstone: 8k Naniwa. Ceramic 0.6. Leather strops /c 1 mic and 0.5 mic diamond paste. Tough steel. Not sure I'm settling on this.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 7 of 20