Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Spyderco Paramilitary 2 CF 3.44 1.41 S90V 62 19 L - 20 R 3.5 um Bottom A.5
 
Authors Comments:Maintains the manufactures angle
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Smith SWBLOP3 3.4 ? 4034 ? 20 3.5 mu ? B ever day use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MelvinSharp
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Delica 4 2.875" 2.5mm VG-10 N/A 20 degrees 3.5 micron strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Strider GW/AR152 8" .250 S30V unknown 25 3.5 micron Bottom C OCONUS deployment
 
Authors Comments:I'll check the hardness when I see the knife again
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Zero Tolerance 0560/0561 3.75 in 0.157 Elmax 60 left 25/right 26 3.5 micro leather bottom B.5 EDC
 
Authors Comments:Not the sharpest thing in the world but will keep that edge for quite some time.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JosephMurray
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Peter Altenbach Chefs Knife 10" 3mm X45CrMoV15 ? 20 2k Chosera Bottom E Chopping and Slicing
 
Authors Comments:I've had this knife for over 24 years and have used it regularly. The steel isn't spectacular and really doesn't hold up well below 20 degrees. I like the shoulders polished and the edge just a little toothy. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
J. A. Henckels Professional "S" 31021-160 Chef 6" 3mm X50CrMoV15 ? 20 2k Chosera Bottom C Chopping and Slicing
 
Authors Comments:Not the greatest steel, doesn't hold its edge well, especially below 20 degrees. -Clay Allison
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Benchmade 915 Triage 3.5" 0.13" N680 57-59HRC 20 1um Strops Bottom B
 
Authors Comments:I rested the spine on the closest pin of the depth key and then rotated the blade until most of it was parallel to the base of the sharpener.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Blur 3.3125" .125" ZDP-189 64HRC 17 1um Bottom. A.5 EDC (Every day carry)
 
Authors Comments:After several months of experimenting, I've settled on 17 degrees for this knife. It gives great performance and holds its edge well. I keep it pretty polished for show and sometimes it's a little too smooth for the work it does so I might put a slightly toothy, almost invisible micro-bevel on it.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Wusthof Classic 10" Slicer 10" .110 X50CrMo14 56-57 RHC 20 1k-1.6k Top C General purpose kitchen utility, cuts lots of vegg
 
Authors Comments:I'd love to go more acute than 20 degrees but the edge just won't hold long enough. I keep it just a little toothy to compensate and it performs well. This is my wife's favorite knife and she uses and abuses constantly.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 9 of 19