Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Heckles Professional S paring 4 inches ? "High carb stainless ? 17.8 ? Above upper holes B Kitchen
 
Authors Comments:Diamond: 600 to 1000. Ceramic:1200 to 0.6 mic. Final: naniwa 8k
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Western 822 Barlow 3 3/8 ? ? ? 22 ? Upper holes A.5 Tool box / barn/ gen utility
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Twist Master 3.5 ? Carbon V ? 17.3 8k Naniwa super stone Upper holes B EDC
 
Authors Comments:Diamond 400-1000. Ceramic 1200-0.6. Naniwa 8k. Bought several of these as close outs/ factory 2nds About 20 years ago. Takes a nice edge easily and keeps it well. Rusts easily.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Strider SnG 3.5 .165 S30V Unknown 24 Degree Bevel with 26 Degree Stropping (Widen arms for Stropping) 600 Grit Bevel, 10 Micron Stropping Top. B.8 Tactical
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
CRKT Folts Minimalist 127mm 2.1mm 5Cr15MoV 57 RC 19 5u Lap Top 30mm Tip to CL/Vise EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
reprofile to 19, finish 1000 diamond
Setting 2:
reprofile to 19, then finish at 0.3u
Setting 3:
0.3 lap then fine strop .5u on leather
Setting 4:
Setting 5:


 Author: BassLakeDan
Rating:
5		 Rating:
8		 Rating:
6		 Rating:
 Rating:
Benchmade Presidio Ultra 2.97" 0.115" 440C Stainless Stee 58-60HRC 15.25 (Measured) 5u Balsa, 3u and 1u 3M PSA Strips (50 passes per side) Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT M21-14SF 3.875 inches 0.14 inches AUS 8 58-59 18.5 5 micron Bottom A 0.5 Put a usable polished sharp edge in place.
 
Authors Comments:I will test the durability and usability of this edge in the coming weeks.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JG
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Zero Tolerance 0700 3.375" Unknown S30V Unknown 14.5 As Measured (15 Degree Slot) 3u Balsa 1u 3M PSA Tape (200 Passes Each) Top B.0 EDC / Boxes / Paper
 
Authors Comments:Tape thumb studs because stones may rub them. S30V is some hard steel!. Great Tanto Shape. My Favorite Blade!
Angle/Finish Tried with Ratings
Setting 1:
14.5 EDC / Paper / Boxes with Mirror Bevel
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Recon 1 Tanto Plain 27TLT 4" 3.5mm AUS 8A Stainless Unknown 19.4 Measured (I align using divots, hence weird angle) 3u Balsa Top B.5 Scaring People
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
19.4 Measured.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
6		 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 6 of 20