Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Kershaw Needs Work 3" forgot to measure 12C26 stainless 58 15 1600 diamond and hand stropped with green rouge top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Black Sable 4" .125" San Mai III 58 HRC 18 primary bevel, 19 degree micro bevel 1600# Top B.5 EDC
 
Authors Comments:I originally created the bevels at 18 degrees and polished them to .5 microns before adding a micro-bevel at 19 degrees with the 1600# ceramic stones to give a mirrored bevel and slightly reduced shoulder while making the actual edge a little wider and giving it some micro teeth.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
SOG Field Pup 4" .125" AUS-8 57-58HRC 20 1600# Top A.5 Field Dressing, Skinning
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Beretta Loveless Drop Point 3.81 .11 AUS-8 57-59 22 1600# Bottom B Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT 4102 Michael Walker BladeLock II 2.875" Unknown AUS-4 Unknown 15 1600# Ceramic Top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Chris Reeve Large Sebenza 3.625" 0125" S35VN 58-59 RC 17 Deg. with 18 Deg. Microbevel 17 Deg. finished at 3.5u Strop Top Holes A.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
17 degree main bevel 18,19,20,21 micro for convex

Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
9		 Rating:
 Rating:
 Rating:
 Rating:
Chris Reeve Small Sebenza 21 2.94" .125" S35VN Stainless Stee 58-59 RC 18 deg. with 19,20 deg. Micro bevel for convex 18 Deg finished with Roo Strop .125 CBN and blank Top Holes B EDC
 
Authors Comments:All angles set with Angle Cube, rechecked on each stone. Re-created 18 Degree bevel with Diamond 400 -1000, Ceramic 1200/1600 then 5000/10000 Chosera. With 5/10k Chosera reset angle to 20 , 19 then back to 18deg. to define convex. Continued with Balsa 20, 19 then 18deg. with .5 Microne paste Completed at 18deg finish with Roo with .125 Cubic Boron then blank Roo with a mist of alcohol. Shaving sharp and developing a nice mirror polish edge. Maintenance additional careful stropping will r
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JamesBell
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 551 1303 3.4 .115 CPM M4 59-61 15 1k Chosera, 3.5 Strops Top A.75 EDC
 
Authors Comments:Needed top depth at 15 deg. Might try alignment "B" next time to get bevel more even (A.75 is a little bevel at tip)
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT M16-13T 3.5" 0.110" AUS8 58-59 Asymmetrical grind (70/30), I used left 20, right 15 to get close and finished the profile that way 1k diamond -> 5um strop for finish and touchup Unique (see comment) B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber Mini Covert 3" 0.110" 154CM Not listed 19 1k diamond for duty/carry, but takes well to full out mirror polish too! Top A.5 EDC
 
Authors Comments:In matching the factory bevel, an even 19 degrees per side ends up 18 on the left arm and 20 on the right arm. Thus far the 19 degree edge has held up very well, as a 154CM should!
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 9 of 20