Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Buck 119BKS-B 6 ? 440C ? 20 3.5um Bottom C Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM0501 Ken Onion Utility Knife 5" ? VG10 61 16 3.5um Top C Cooking - general purpose kitchen utility
 
Authors Comments:Used the top holes but only rested the spine on the prong closest to me and rotated the blade to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
16 Degrees, Top Holes, Align=C, Finish=3.5um
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
9		 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0516 Ken Onion Paring Knife 3" ? VG10 61 16 3.5um Top B Cooking, paring
 
Authors Comments:Set spine on the pin closest to me and then rotated the edge to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0500 8" ? VG10 61 16 3.5um Bottom D Chopping, slicing, general cooking
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Recon 1 Tanto Plain 27TLT 4" 3.5mm AUS 8A Stainless Unknown 19.4 Measured (I align using divots, hence weird angle) 3u Balsa Top B.5 Scaring People
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
19.4 Measured.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
6		 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Zero Tolerance 0700 3.375" Unknown S30V Unknown 14.5 As Measured (15 Degree Slot) 3u Balsa 1u 3M PSA Tape (200 Passes Each) Top B.0 EDC / Boxes / Paper
 
Authors Comments:Tape thumb studs because stones may rub them. S30V is some hard steel!. Great Tanto Shape. My Favorite Blade!
Angle/Finish Tried with Ratings
Setting 1:
14.5 EDC / Paper / Boxes with Mirror Bevel
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
CRKT M21-14SF 3.875 inches 0.14 inches AUS 8 58-59 18.5 5 micron Bottom A 0.5 Put a usable polished sharp edge in place.
 
Authors Comments:I will test the durability and usability of this edge in the coming weeks.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JG
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade Presidio Ultra 2.97" 0.115" 440C Stainless Stee 58-60HRC 15.25 (Measured) 5u Balsa, 3u and 1u 3M PSA Strips (50 passes per side) Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT Folts Minimalist 127mm 2.1mm 5Cr15MoV 57 RC 19 5u Lap Top 30mm Tip to CL/Vise EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
reprofile to 19, finish 1000 diamond
Setting 2:
reprofile to 19, then finish at 0.3u
Setting 3:
0.3 lap then fine strop .5u on leather
Setting 4:
Setting 5:


 Author: BassLakeDan
Rating:
5		 Rating:
8		 Rating:
6		 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 14 of 20