Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Strider PT 2.87 0.125 S30V Unknown 30 3.5um Bottom. A.25
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
KAI/Zero Tolerance 0560 3.75 0.157 Elmax 60-61 20 10K Choseras Bottom. B 0.25
 
Authors Comments:The 10K Chosera edge is not really functional (unless you want to cut single sheets of paper). But it looks great.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Becker BK16 4.375 0.165 1095 56-58 20 1600 Bottom. B 0.5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Stretch 2 CF 3.5" .125" ZDP-189 64HRC 15 3.5um Bottom... B
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Boker Plus Toucan multi tool neck knife 1.02 inches / 2.6cm 0.2 inches / 5mm 440c 58 HRC 22* factory angle 0.6 mic ceramic Level @ grind line 0.8 A Neck knife multi tool
 
Authors Comments:Depth level with grind line
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Fallkniven A1 6.3 0.24 VG-10 59 15 1600 Low B 0.75
 
Authors Comments:I put a 15 degrees microbevel on top of a 13 degrees convex edge
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Buck Metro (759) 1" ? 420HC ? 17 1000# diamond, a few light cleanup passes with 5um leather See comments A.5 EDC
 
Authors Comments:Clamp on the bottle opener ring, the aluminum body section will control depth. Align to A.5 and level out the little blade with the clamp as best you can! Works surprisingly well.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Spec Elite 1 3.75" 1/8" Seki Japan VG10 60-61 HRC 16 degrees 3.5micron shallow dept C thumb knob onClamp EDC light to moderate use
 
Authors Comments:difficult to set up in Clamp, recommend removing thumb knob for sharpening entire blade length
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Leaf Storm 2.125" .125" CPMS30V unknown 15 1000 Grit Short Short, very short Pocket knife
 
Authors Comments:NA
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Leatherman Super Tool (original) 3" n/a n/a (cheap) n/a 22 1000# then 5-3.5 leather strops spine only in vice A .5 EDC
 
Authors Comments:set blade high in vice, only the square part of spine in vice
Angle/Finish Tried with Ratings
Setting 1:
lower in vice with depth key at high
Setting 2:
22 deg, 1000#, 3.5u strops, depth higher, see comm
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
4		 Rating:
6		 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 8 of 20