Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
SOG X Ray Vision Mini 3" .12" VG-10 59-60 23 to 25 1000 Top A .5
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Buck Protege 450T 3" .1 420HC 58-61 18, 20 Micro 3.5 um@18, 1000@20 Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck 112 3" .077 420HC 58-61 18, 20 Micro 3.5 um@18, 1600@20 Top B Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Needs Work 3" forgot to measure 12C26 stainless 58 15 1600 diamond and hand stropped with green rouge top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber Mini Covert 3" 0.110" 154CM Not listed 19 1k diamond for duty/carry, but takes well to full out mirror polish too! Top A.5 EDC
 
Authors Comments:In matching the factory bevel, an even 19 degrees per side ends up 18 on the left arm and 20 on the right arm. Thus far the 19 degree edge has held up very well, as a 154CM should!
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Leatherman Super Tool (original) 3" n/a n/a (cheap) n/a 22 1000# then 5-3.5 leather strops spine only in vice A .5 EDC
 
Authors Comments:set blade high in vice, only the square part of spine in vice
Angle/Finish Tried with Ratings
Setting 1:
lower in vice with depth key at high
Setting 2:
22 deg, 1000#, 3.5u strops, depth higher, see comm
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
4		 Rating:
6		 Rating:
 Rating:
 Rating:
Cold Steel Voyager (Medium Tanto) 3" 3 mm AUS 8A HRC 57-59 19 3.5um 1st A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Shun DM-0516 Ken Onion Paring Knife 3" ? VG10 61 16 3.5um Top B Cooking, paring
 
Authors Comments:Set spine on the pin closest to me and then rotated the edge to horizontal.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Native 5 3" .125" CPM S35VN HRC 59-62 17 0.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade Emissary 470-1 3 inches 0.09 inches S30-v 58-60 HRC 21.75*. (? Factory?) Leather strop 0.5 mic Upper holes A.5 EDC
 
Authors Comments:Stone progression: diamond 1000; ceramic: 1.4, 1200, 1600. Superstone: 8k Naniwa. Ceramic 0.6. Leather strops /c 1 mic and 0.5 mic diamond paste. Tough steel. Not sure I'm settling on this.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 13 of 20