Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Cold Steel Old small folder 2.5 inches ? San Mai 3 ? 56-58 HRC ? 18.4* 0.6 mic ceramic Upper holes A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Twitch II 2.68" .1" AUS-8 HRC 57-58 22 3.5u Top A.5
 
Authors Comments:My progression was 800 to 1600 ceramics. Then 14, 10, 5, 3.5u strops. 100 strokes with each strop then would flip strops end for end at 50 so the whole strop would get worn evenly
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cutco 2 3/4" paring Item # 1720 2.75 - 440A - 17 1000# then 5-3.5 leather strops spine only in vice A.5 kitchen, general use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
A.5, 17 deg.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Victorinox Swisschamp 2.75 0.09 Proprietary 56 20 Chosera 10K Top B .
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Cryo 1555TIX 2.75 inch ? 8Cr13MoV ? 22* per side Leather /c 0.5 mic diamond Upper A.5 Sons 1st interesting knives
 
Authors Comments:Diamond 800, 1000. Ceramic 1.4, 1200,1600. Naniwa 8k. Ceramic 0.6. Leather strops 1
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Persistence 2.75" 0.125" 8Cr13MoV HRC 58-59 15 0.5um 1st B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Leek 1660BR 2.825 .09 Sandvik 14C28N unk 17 .6 ceramics top A EDC backup
 
Authors Comments:nice knife for an office enviroment (not too threatning) seems to hold the edge pretty well with minimal touching up so far. Haven't used it for anything heavy duty yet, though.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Strider PT 2.87 0.125 S30V Unknown 30 3.5um Bottom. A.25
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
CRKT 4102 Michael Walker BladeLock II 2.875" Unknown AUS-4 Unknown 15 1600# Ceramic Top A5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Delica 4 2.875" 2.5mm VG-10 N/A 20 degrees 3.5 micron strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 4 of 20