Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Reinhard Müller MSP Linerlock 85 mm 3,7 mm CPMS90V HRC 58 18 0.5 um paste on leather strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: johpe
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Fontignac Sujihiki 27 cm ? VG10 55 18 Chosera 10K Bottom C 0.5 ?
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: mark76
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Heckles Professional S paring 4 inches ? "High carb stainless ? 17.8 ? Above upper holes B Kitchen
 
Authors Comments:Diamond: 600 to 1000. Ceramic:1200 to 0.6 mic. Final: naniwa 8k
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kabar Mule Tanto 3-13/16" 0.135 mm 3Cr13 HRC 57-59 17.5 3.5um 2 B Tactical
 
Authors Comments:Reprofiled with 50/80 stones to 17.5 degree on each side. Knife if built like tank and the angle holds through abuse. Used all the stones from 50/80 to 1200/1600, then taped 2500 grit sandpaper to the ceramics. Stropped after all that, finishing with 3.5um for a mirror finish
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber EZ Out 3 .1 high carbon stainles n/a 17.5 1000# then 5-3.5 leather strops Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
1000# 17.5 deg., stop @ 16.5
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 556 Mini Griptilian 2.9 0.10 154 cm 58-61 17.5 10k chosera, 0.5 strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
17.5 deg.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Geocyclist
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Twist Master 3.5 ? Carbon V ? 17.3 8k Naniwa super stone Upper holes B EDC
 
Authors Comments:Diamond 400-1000. Ceramic 1200-0.6. Naniwa 8k. Bought several of these as close outs/ factory 2nds About 20 years ago. Takes a nice edge easily and keeps it well. Rusts easily.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
ESEE ESEE-5 5.45 inches .25 inches 1095 cabon steel 57 17-19-21 convexed ceramics then strops 5 and 3.5 pastes to integrate the shoulders top B-5 bushcraft and survival
 
Authors Comments:This knife is essentially a pry bar with a sharp edge. It is a beast developed to help downed helicopter pilots to escape from their wreckage. A great knife to carry around in your car for emergencies. LJM
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Delica 4 2.88 0.093 ZDP-189 64 17, Mirco 20 3.5 um @19 Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 13 of 20