Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Buck 425 1 7/8 ? 420HC 58 19 .6 Micron Ceramic Above TOP A .25 Pocket
 
Authors Comments:Make sure you have it above the top Depth holes or you will be hitting your vise.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JacobNoes
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT M16-14T 3.875 inches 0.14 inches AUS 8 58-59 HRC 19 Bead-Blast Bottom A 0.5 EDC
 
Authors Comments:Chisel Ground Tanto. I focused on the primary side nocking the burr off the back side down to 400 grit. After 400 grit I sharpened all the way down to 3.5 micron leather strops. Holds a great edge for a long time under normal daily use.
Angle/Finish Tried with Ratings
Setting 1:
18 degree, stropped to 3.5 microns, Very effective
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: JG
Rating:
10		 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Paramilitary 2 CF 3.44 1.41 S90V 62 19 L - 20 R 3.5 um Bottom A.5
 
Authors Comments:Maintains the manufactures angle
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Gerber Profile 3.5 .13 440C 58-61 19, 20 micor 3.5 um@19, 1000@20 Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck Ranger 110 3.75" .1 420HC 58-61 19, 20 Micro 3.5 um@19, 1000@20 Top B.5 Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 553 Griptilian Tanto 3.45" 0.115" 154CM Stainless Stee 58-60HRC 19.4 (left). 16.5 (right) Measured. Forward 3u Balsa 1u 3M PSA Tape Top A.5 (Angled) Maintain Factory Edge
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Factory Edge. Cuts Paper Great. No Hair Whittling.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Recon 1 Tanto Plain 27TLT 4" 3.5mm AUS 8A Stainless Unknown 19.4 Measured (I align using divots, hence weird angle) 3u Balsa Top B.5 Scaring People
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
19.4 Measured.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: EatingPie
Rating:
6		 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Finn Bear 4" 2.5 mm Krupp 4116 Stainless HRC 56-57 19.5 (39 inclusive) .5um Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
ESEE Laser Strike 4.75" .1875" 1095 55-57RC 19A 10um Strop after 600# Diamond Stone Bottom B.5 Bushcraft, Survival, Camping
 
Authors Comments:I haven't tested the edge of this blade yet, will do some cutting and experimenting before fully commenting.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
10		 Rating:
10		 Rating:
10		 Rating:
10		 Rating:
10
Wusthof Classic 10" Slicer 10" .110 X50CrMo14 56-57 RHC 20 1k-1.6k Top C General purpose kitchen utility, cuts lots of vegg
 
Authors Comments:I'd love to go more acute than 20 degrees but the edge just won't hold long enough. I keep it just a little toothy to compensate and it performs well. This is my wife's favorite knife and she uses and abuses constantly.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 11 of 20