Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Smith SWBLOP3 3.4 ? 4034 ? 20 3.5 mu ? B ever day use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MelvinSharp
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck Protege 450T 3" .1 420HC 58-61 18, 20 Micro 3.5 um@18, 1000@20 Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Gayle Bradley 3.5 1/8 CPM M4 I think about 62 RC 15 1 micron boron carbide(HandAmercian) on balsa Top B EDC
 
Authors Comments:I like this steel. It takes a variety of finishes well but for EDC I like a congress 400 or the 1000 diamonds followed by 1 micron boron carbide paste on balsa the best. This seems to be about where hair whittling starts but it still has some bite. Hope you like it as much as I do.
Angle/Finish Tried with Ratings
Setting 1:
17 degrees 1000 diamond 3.5 paste on balsa
Setting 2:
15 degrees 1000 diamond 1 BC on balsa
Setting 3:
15 degrees 400 congress 1 BC on balsa
Setting 4:
15 degrees all the way to .125 CBN on roo
Setting 5:


 Author: guest
Rating:
6		 Rating:
7		 Rating:
9		 Rating:
8		 Rating:
Buck 112 3" .077 420HC 58-61 18, 20 Micro 3.5 um@18, 1600@20 Top B Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber Profile 3.5 .13 440C 58-61 19, 20 micor 3.5 um@19, 1000@20 Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Emerson CQC-8 100 mm 3 mm 154CM? 57-59 23 1000# Diamond Bottom B Hard use survival / bushcraft
 
Authors Comments:This folder is from 2004 without wave. I have a V-grind on this one.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Heckles Professional S paring 4 inches ? "High carb stainless ? 17.8 ? Above upper holes B Kitchen
 
Authors Comments:Diamond: 600 to 1000. Ceramic:1200 to 0.6 mic. Final: naniwa 8k
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Cold Steel Finn Bear 4" 2.5 mm Krupp 4116 Stainless HRC 56-57 19.5 (39 inclusive) .5um Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 551 Griptilian 3.45" .115" 154CM 58-60HRC 18 deg. w/ 20 deg. microbevel 3.5m on Balsa Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: cbwx34
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
CRKT M16-13T 3.5" 0.110" AUS8 58-59 Asymmetrical grind (70/30), I used left 20, right 15 to get close and finished the profile that way 1k diamond -> 5um strop for finish and touchup Unique (see comment) B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 11 12 13 14 15 16 17 18 19 20 Next > End >>
Page 11 of 20