Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Kershaw 1745 3 1/4 in. 1/8 in. 14C28N Unk. 17-18 deg. 2ndry with 20 deg. primary .625 Ceramic Top B EDC
 
Authors Comments:Had a rough 17-18 deg. edge on it... Lightly used the 1000g diamond to clean up the edge, then finished by going thru ceramics to the .625m. Came out very sharp, with a nice little bite to it.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kershaw ZT 0560 3.75" .1625" Elmax 60-62 HRC 19 Micro-Fine .6 Bottom B EDC
 
Authors Comments:So far I love the knife and the settings I've chosen. It's extremely aggressive and very durable.
Angle/Finish Tried with Ratings
Setting 1:
19 degrees, AC verified. .6 Micro-Fine Finish.
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Benchmade 581 Barrage 3.60" .121" M390 60-62 17 deg. (measured) .5m Leather (although lightly stropped so not a mirror finish). Top B EDC
 
Authors Comments:1st time w/ M390 steel. Slightly lowered factory bevel and cleaned up the edge (came with a very rough finish). See how it holds up at this angle.
Angle/Finish Tried with Ratings
Setting 1:
A.5 and 17.5º
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: cbwx34
Rating:
7		 Rating:
 Rating:
 Rating:
 Rating:
Beretta Loveless Drop Point 3.81 .11 AUS-8 57-59 22 1600# Bottom B Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Smith SWBLOP3 3.4 ? 4034 ? 20 3.5 mu ? B ever day use
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MelvinSharp
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Buck Protege 450T 3" .1 420HC 58-61 18, 20 Micro 3.5 um@18, 1000@20 Top B Hunting
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Gayle Bradley 3.5 1/8 CPM M4 I think about 62 RC 15 1 micron boron carbide(HandAmercian) on balsa Top B EDC
 
Authors Comments:I like this steel. It takes a variety of finishes well but for EDC I like a congress 400 or the 1000 diamonds followed by 1 micron boron carbide paste on balsa the best. This seems to be about where hair whittling starts but it still has some bite. Hope you like it as much as I do.
Angle/Finish Tried with Ratings
Setting 1:
17 degrees 1000 diamond 3.5 paste on balsa
Setting 2:
15 degrees 1000 diamond 1 BC on balsa
Setting 3:
15 degrees 400 congress 1 BC on balsa
Setting 4:
15 degrees all the way to .125 CBN on roo
Setting 5:


 Author: guest
Rating:
6		 Rating:
7		 Rating:
9		 Rating:
8		 Rating:
Buck 112 3" .077 420HC 58-61 18, 20 Micro 3.5 um@18, 1600@20 Top B Field Dressing Game
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: guest
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber Profile 3.5 .13 440C 58-61 19, 20 micor 3.5 um@19, 1000@20 Top B EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Emerson CQC-8 100 mm 3 mm 154CM? 57-59 23 1000# Diamond Bottom B Hard use survival / bushcraft
 
Authors Comments:This folder is from 2004 without wave. I have a V-grind on this one.
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: jolut
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 8 of 20