Knife Database
   
⇔ Manufacturer ⇔ Model ⇔ Blade Length ⇔ Thickness ⇔ Steel ⇔ Hardness ⇔ Recommended Angle ⇔ Recommended Finish ⇔ Depth ⇔ Alignment⇔ Intent
Spyderco Delica 4 2.875" 2.5mm VG-10 N/A 20 degrees 3.5 micron strop Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Spyderco Paramilitary 2 CF 3.44 1.41 S90V 62 19 L - 20 R 3.5 um Bottom A.5
 
Authors Comments:Maintains the manufactures angle
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author:
Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1		 Rating:
1
Kershaw ET 3.25" 0.120" Sandvik 14C28N Not listed 20 1000 grit diamond, 5um paste on leather optional Top A.5 General light utility
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Delica 4 2.88 0.093 ZDP-189 64 17, Mirco 20 3.5 um @19 Top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: TPeters
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Kershaw Needs Work 3" forgot to measure 12C26 stainless 58 15 1600 diamond and hand stropped with green rouge top A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: xuzme720
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Western 822 Barlow 3 3/8 ? ? ? 22 ? Upper holes A.5 Tool box / barn/ gen utility
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Gerber Mini Covert 3" 0.110" 154CM Not listed 19 1k diamond for duty/carry, but takes well to full out mirror polish too! Top A.5 EDC
 
Authors Comments:In matching the factory bevel, an even 19 degrees per side ends up 18 on the left arm and 20 on the right arm. Thus far the 19 degree edge has held up very well, as a 154CM should!
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: ApexGS
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Leatherman PST-original Leatherman multi-tool 2.9 inches ? 420 HC STAINLESS ? 20 1200 ceramic Above upper holes A.5 Multi tool/ anything goes
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: Mikedoh
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
SOG Twitch II 2.68" .1" AUS-8 HRC 57-58 22 3.5u Top A.5
 
Authors Comments:My progression was 800 to 1600 ceramics. Then 14, 10, 5, 3.5u strops. 100 strokes with each strop then would flip strops end for end at 50 so the whole strop would get worn evenly
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: wickededge
Rating:
 Rating:
 Rating:
 Rating:
 Rating:
Spyderco Ambitious 2.25" 0.125" 8Cr13MoV HRC 58-59 15 0.5um 1st A.5 EDC
 
Authors Comments:
Angle/Finish Tried with Ratings
Setting 1:
Setting 2:
Setting 3:
Setting 4:
Setting 5:


 Author: MartinL1
Rating:
 Rating:
 Rating:
 Rating:
 Rating:

<< Start < Prev 1 2 3 4 5 6 7 8 9 10 Next > End >>
Page 4 of 20