Welcome, Guest
Username: Password: Remember me
Welcome to the Wicked Edge forum!

Tell us and our members who you are, what you like and why you became a member of this site.
We welcome all new members and hope to see you around a lot!

TOPIC: You never know until...

You never know until... 1 year 11 months ago #5140

  • hemdale
  • hemdale's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 3
  • Thank you received: 1
  • Karma: 3
...you try.

I had the Spyderco TriEdge: marvelous but my hand are not that accurate when it comes to keeping the same angle for 45 mins.
I just received the DMT Aligner today and I'm returning it tomorrow. I have no words that can describe this sharpener :sick: :sick: :sick:

Mitch (BB) told me it could be a good idea to join this forum (eventhough I don't have the WE...yet).
So here I am, a french guy from London and I'm definitely convinced that I should give the WE a try and hopefully buy it !

Cheers guys.

Bruce
The administrator has disabled public write access.

Re: You never know until... 1 year 11 months ago #5141

  • KenBuzbee
  • KenBuzbee's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 397
  • Thank you received: 110
  • Karma: 22
Welcome Bruce.

I'm new here myself but there is a wealth of information here and a lot of very helpful folks to answer your questions.

My first piece of advice is to check out the videos (and on YouTube) and you'll get a sense of what the WEPS brings to the table.

I've had mine for a couple months now and turning out some of the best edges I've ever done.

Have fun,

Ken
玉鋼
The administrator has disabled public write access.

Re: You never know until... 1 year 11 months ago #5142

  • hemdale
  • hemdale's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 3
  • Thank you received: 1
  • Karma: 3
Thanks Ken !

Any kind of best edge on specific steel in particular ?
The administrator has disabled public write access.
The following user(s) said Thank You: Rmorris7

Re: You never know until... 1 year 11 months ago #5143

  • KenBuzbee
  • KenBuzbee's Avatar
  • OFFLINE
  • Platinum Boarder
  • Posts: 397
  • Thank you received: 110
  • Karma: 22
BruceBarelly wrote:
Thanks Ken !

Any kind of best edge on specific steel in particular ?

I've gotten great edges on everything from a vintage carbon steel chefs knife I use daily to a small VG10 Spyderco Balance to my Super Blue Cally 3.5. Lining up to do an S90V Manix 2 in the not too distant future. If I could figure out the mounting I'd do my H1 Spyderhawk but I may just have to mount it up and see what happens ;)

Anything specific you wanted to know about?

Ken
玉鋼
The administrator has disabled public write access.
The following user(s) said Thank You: hemdale

Re: You never know until... 1 year 11 months ago #5145

  • hemdale
  • hemdale's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 3
  • Thank you received: 1
  • Karma: 3
I need to take care of my babies:

Fallkniven S1 (VG 10) ... and tiny slightly bit chipped...
Mcusta Bamboo (VG 10)
Benchmade MiniGrip Doug Ritter (S30V)
CRK Small Sebenza (S35VN)
The administrator has disabled public write access.

Re: You never know until... 1 year 11 months ago #5146

  • leomitch
  • leomitch's Avatar
  • OFFLINE
  • Administrator
  • Posts: 719
  • Thank you received: 207
  • Karma: 92
WEPS will provide the best care for your babies mate. Give Clay a call my friend. When you are ready!

Best to you chum
Leo
Never go anywhere without your knife!
Gibbs rule number 9

Leo James Mitchell
The administrator has disabled public write access.
Time to create page: 0.135 seconds